Roland juno-ds61, Parameter Manual

Page: 42 / 88

42
MFX/Chorus/Reverb Parameters
04: LOW BOOST
Boosts the volume of the lower range, creating powerful lows.
L in
R in
L out
R out
Low Boost
2-Band EQ
2-Band EQ
Low Boost
Parameter
Value Explanation
Boost Frequency # 50–125[Hz]
Center frequency at which the lower
range will be boosted
Boost Gain # 0–+12[dB]
Amount by which the lower range will
be boosted
Boost Width WIDE, MID, NARROW
Width of the lower range that will be
boosted
Low Gain -15–+15[dB] Gain of the low frequency range
High Gain -15–+15[dB] Gain of the high frequency range
Level 0–127 Output level
05: SUPER FILTER
This is a filter with an extremely sharp slope. The cutoff frequency can be varied
cyclically.
L in
R in
L out
R out
Super Filter
Super Filter
Parameter Value Explanation
Filter Type
Filter type
Frequency range that will pass through each filter
LPF
Frequencies below the cutoff
BPF Frequencies in the region of the cutoff
HPF Frequencies above the cutoff
NOTCH Frequencies other than the region of the cutoff
Filter Slope
Amount of attenuation per octave
-12[dB]
Gentle
-24[dB] Steep
-36[dB] Extremely steep
Filter Cutoff # 0–127
Cutoff frequency of the filter
Increasing this value will raise the cutoff
frequency.
Filter Resonance #
0–127
Filter resonance level
Increasing this value will emphasize the region
near the cutoff frequency.
Filter Gain 0–+12[dB] Amount of boost for the filter output
Modulation Sw
OFF, ON On/off switch for cyclic change
Modulation Wave
How the cutoff frequency will be modulated
TRI
Triangle wave
SQR Square wave
SIN Sine wave
SAW1 Sawtooth wave (upward)
SAW2 Sawtooth wave (downward)
SAW1 SAW2
Rate # 0.05–10.00[Hz], note Rate of modulation
Depth
0–127 Depth of modulation
Attack # 0–127
Speed at which the cutoff frequency will change
This is effective if Modulation Wave is SQR,
SAW1, or SAW2.
Level 0–127 Output level
06: STEP FILTER
This is a filter whose cutoff frequency can be modulated in steps. You can specify
the pattern by which the cutoff frequency will change.
L in
R in
L out
R out
Step Filter
Step Filter
Parameter Value Explanation
Step 01–16 0–127 Cutoff frequency at each step
Rate # 0.05–10.00[Hz], note Rate of modulation
Attack # 0–127
Speed at which the cutoff frequency changes
between steps
Filter Type
Filter type
Frequency range that will pass through each filter
LPF
frequencies below the cutoff
BPF frequencies in the region of the cutoff
HPF frequencies above the cutoff
NOTCH frequencies other than the region of the cutoff
Filter Slope
Amount of attenuation per octave
-12[dB]
gentle
-24[dB] steep
-36[dB] extremely steep
Filter Resonance # 0–127
Filter resonance level
Increasing this value will emphasize the region
near the cutoff frequency.
Filter Gain
0–+12[dB] Amount of boost for the filter output
Level 0–127 Output level
MEMO
You can use MFX control to restart the step sequence from the beginning (p. 18,
p. 24).
07: ENHANCER
Controls the overtone structure of the high frequencies, adding sparkle and
tightness to the sound.
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
2-Band
EQ
2-Band
EQ
Parameter Value Explanation
Sens # 0–127 Sensitivity of the enhancer
Mix # 0–127 Level of the overtones generated by the enhancer
Low Gain
-15–+15[dB] Gain of the low range
High Gain -15–+15[dB] Gain of the high range
Level 0–127 Output Level
08: AUTO WAH
Cyclically controls a filter to create cyclic change in timbre.
L in
R in
L out
R out
Auto Wah
2-Band EQ
2-Band EQ
Auto Wah
Parameter Value Explanation
Filter Type
Type of filter
LPF
The wah effect will be applied over a wide
frequency range.
BPF
The wah effect will be applied over a narrow
frequency range.
Manual # 0–127
Adjusts the center frequency at which the effect
is applied.
Peak 0–127
Adjusts the amount of the wah effect that will
occur in the range of the center frequency.
Set a higher value for Q to narrow the range to
be affected.
Sens # 0–127
Adjusts the sensitivity with which the filter is
controlled.
Polarity
Sets the direction in which the frequency will change when the auto-
wah filter is modulated.
UP
The filter will change toward a higher frequency.
DOWN The filter will change toward a lower frequency.
Rate # 0.05–10.00[Hz], note Frequency of modulation
Depth # 0–127 Depth of modulation
Phase # 0–180[deg]
Adjusts the degree of phase shift of the left and
right sounds when the wah effect is applied.
Low Gain -15–+15[dB] Gain of the low range
High Gain -15–+15[dB] Gain of the high range
Level 0–127 Output level
3
3
3
3
3