Roberts Gorden VANTAGE HEV-100 Installation, Operation & Service Manual Download

Page: 31 / 80

SECTION 6: H

EATER

NSTALLATION

FIGURE 22: Swirler Installation Model: HEV-125, 30’ U-Tube; Swirler Package - 20' (6 m) (p/n 03051511K)

See Page 34

for U-Tube installation instructions.

Coupling

Internal
Coupling Pin

Fold swirler tab
over tube as shown

Swirler
Starter
Section

Pivot Point

Tab

Swirler
Starter
Section

Coupling

Burner Tube

Swirler
Adapter
Section

10’ (3 m) Tube

5’ (1.5 m) Tube (tubes cut in field)

10’ (3 m) Tube

Vent Adapter

U-tube

Swirler
Adapter
Section

Note:

Swirler installation for

this model must be complete
prior to coupling installation
for proper swirler starter tab
placement.

Swirler
Adapter
Section

Pivot Point

Swirler
Adapter
Section

Summary of Contents for VANTAGE HEV-100

















































































Search results

Summary of Contents for VANTAGE HEV-100

Reviews:

Related manuals for VANTAGE HEV-100

Brands by name

Popular brands

Roberts Gorden VANTAGE HEV-100, Installation, Operation & Service Manual

Search results

Summary of Contents for VANTAGE HEV-100

Reviews:

Related manuals for VANTAGE HEV-100

Brands by name

Popular brands