Roberts Gorden VANTAGE HEV-100 Installation, Operation & Service Manual Download | Manualshive

Page: 29 / 80

background image

SECTION 6: H

EATER

I

NSTALLATION

25

Step 6.6 Swirler Installation

Description

Part Number

Swirler Starter 62" (1.6 m)

03051506

Swirler Adapter 62" (1.6 m)

03051507

Tube

91409XXX

Swirler installation required for models
specified in chart below.

Begin installing swirler at end of tube section
as described in the "Swirler Installation" chart
below and continue towards burner.

Note:

If heater length is extended 10' (3 m)

beyond the specified minimum heat
exchanger length swirler can begin in either
the specified tube section (according to the
"Swirler Installation" chart) or the end of the
10' (3 m) extension and continue towards
burner.

Swirler Installation

Model

Tube Section

Swirler Qty

HEV-125

3rd 10' (3 m) Section

2 St 2 Adapters

HEV-150

4th 10' (3 m) Section

1 S 1 Adapter

HEV-175

5th 10' (3 m) Section

2 St 1 Adapter

Swirlers should not to be installed through 180° "U"
sections or elbows. For this reason, 15' and 20' long
swirler packages each contain 2 swirler starter sections
to allow for starter pieces to be installed before and after
"U" sections and elbows. Swirler starter section
identified as section with tab on end. Swirlers should be
installed as shown in figures 21 through 27.

«
...
27
28
29
30
31
...
»

Summary of Contents for VANTAGE HEV-100

















































































Reviews:

No comments

Related manuals for VANTAGE HEV-100

Brand: ABI Attachments Pages: 20

Brand: Salda Pages: 12

Brand: DAYGAS Pages: 32

Brand: Daewoo Pages: 18

Brand: Dexon Pages: 25

Brand: Nortek Pages: 52

Brand: Sunred Pages: 99

Steam Outlet Commercial

Brand: Tylo Pages: 4

TOUCHSCREEN FAR

Brand: Funkyheat Pages: 26

Brand: WMT Pages: 7

Brand: Lynx Pages: 22

Brand: Bard Pages: 27

Brand: Chromalox Pages: 4

Brand: Omega Altise Pages: 8

Brand: SereneLife Pages: 5

Brand: P1 Pages: 44

Brand: aqprox! Pages: 20

Brand: S&P Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands