background image

12

EN

13

EN

Frequency (Auto-ranging)

Sensitivity: >0.5V RMS while  ≤1MHz ;

Sensitivity: >3V RMS while >1MHz ;

Input Protection: 1000V dc or 1000V ac rms. 

Duty Cycle

Pulse width: >100us, <100ms; 

Frequency width: 5Hz – 150kHz

Sensitivity: <0.5V RMS 

Overload protection: 1000V dc or ac rms.

Temperature

Sensor: Type K Thermocouple

Overload protection: 1000V dc or ac rms.

Diode Test

Open circuit voltage: MAX. 3V dc 

Overload protection: 1000V dc or ac rms.

Audible continuity

Audible threshold: Less than50Ω Test current MAX. 1.5mA

Overload protection: 1000V dc or ac rms.

Accessories

Included accessories

Standard Red/Black lead set with test probes

BATTERY and FUSE replacement

WARNING: To avoid electric shock, disconnect the test leads from any source of voltage 

before removing the battery door.

1. When the batteries become exhausted or drop below

the operating voltage, the battery warning symbol will appear in the LCD display. The

battery should be replaced.

2. Follow instructions for installing battery. See the Battery Installation section of this

manual.

3. Dispose of the old battery properly.

BATTERY INSTALLATION

WARNING: To avoid electric shock, disconnect the test leads from any source of voltage 

before removing the battery cover.

Do not operate the instrument with the battery cover removed

1.

Disconnect the test leads from the meter.

2.

Open the battery cover by loosening the screw using a Phillips head screwdriver.

3.

Insert the battery into battery holder, observing the correct polarity.

4.

Put the battery cover back in place. Secure with the two screws.

NOTE: If your meter does not work properly, check the fuses and battery to make sure that 

they are still good and that they are properly inserted.

REPLACING THE FUSES

WARNING: To avoid electric shock, disconnect the test leads from any source of voltage 

before removing the fuse /battery cover.

Summary of Contents for 355-00011


















Reviews: