manualshive.com logo in svg

Riso MZ1070, Technical Manual, Page: 148 / 150

Share
Download
Riso MZ1070 Technical Manual Download Page 148

[ 17-2 ]

MZ870 / MZ890 / MZ1070 / MZ1090

 (Revision 0.9)

OTHER PRECAUTIONS

1.  Downloading the DSP Software

NOTE:  The DSP Software is required to synchronize the Second Paper Feed Motor to the Main Motor.     

The DSP Software is download in the Extension-PCB2.    If the Extension-PCB2 is replaced, the 

DSP Software must be downloaded.

 

The DSP Software changes the speed of the Second Paper Feed Motor when feeding the paper 

from the second paper feed area to the print drum, according to the print drum angle when the 

Timing Roller and Guide Roller start feeding the paper.   This control action keeps the image print 

position constant on all the prints.     The DSP Software also controls the Second Paper Feed Mo

-

tor speed the moment the print drum pinches the leading edge of the paper.   When the leading 

edge of the paper arrives at the print drum, according to the paper size and to which print drum 

the paper is sent to, the trailing edge of the paper is still pinched by the Timing Roller and Guide 

Roller.    The DSP Software makes sure that the Second Paper Feed Motor feeds the paper in the 

same speed as the print drum to ensure smooth paper feeding through the printing area to prevent 

smeared image which may occur if the Timing Roller and Guide Roller pull on the paper during the 

printing.

 

The DSP Software version should match with that of the Mechanical Control PCB and NeoROSA 

PCB firmware.  The compatibility information on the firmware program versions will be issued at 

the same time when updated DSP Software is announced.

(1)  With the appropriate firmware for the mechanical control PCB and for the NeoROASA PCB download

-

ed, turn ON the machine in test mode to confirm that the machine properly goes into Test Mode.

(2)  Switch OFF the machine power and insert the download CF Card in an adopter or in USB Memory 

Stick, containing the DSP software.

(3)  Launch Test Mode and run Test Mode No. 102 [DSP Download (Main, Secondary)].

(4)  Check the operation panel and make sure that the download is completed (The download should take 

around one minute).

(5)  Switch OFF the machine power and remove the CF card or USB memory stick.

(6)  Launch Test Mode again and run Test Mode No. 126 (Optional Configuration Check). Check the soft

-

ware version on the display to confirm that the DSP Software is upgraded.

MZ7 & MZ9 Series contain the DSP Software in the Mechanical Control PCB.

MZ8 & MZ10 Series contain the DSP Software in the Extension-PCB2.

Summary of Contents for MZ1070























































































































































Reviews:

No comments