manualshive.com logo in svg

Riso MZ1070, Technical Manual, Page: 103 / 150

Share
Download
Riso MZ1070 Technical Manual Download Page 103

[ 16-69 ]

MZ870 / MZ890 / MZ1070 / MZ1090

 (Revision 0.9)

PANEL MESSAGE

Error type

T51 [Print pressure control pulse motor lock]   (Drum No.2)

Panel display

T51-*** 

!!System Error!! 

Press Reset Key 

If Recovery has Failed, Call Service

Error reset 

method

Press the Reset key or switch power OFF, then ON.

Error point

Error detecting condition

600

The print pressure control sensor does not change from OFF to ON within 3.9 seconds 

after the print pressure control pulse motor activates to increase pressure during home 

positioning.

601

The print pressure control sensor does not change from ON to OFF within 4.6 seconds 

after the print pressure control pulse motor activates to reduce pressure during home 

positioning.

602

Although the print pressure control pulse motor has completed the operation in 

sensor stop mode, the logical value of the sensor at the arrival point does not match 

the design value, or the operation fails to complete in counter stop mode within the 

specified time.

Error type

T52 [Master disposal section motor lock]   (Drum No.2)

Panel display

T52-*** 

!!System Error!! 

Press Reset Key 

If Recovery has Failed, Call Service

Error reset 

method

Press the Reset key.

Error point

Error detecting condition

300

Overload current detected in master disposal motor.

 

The master disposal motor over current was detected 5 times consecutively (polling at 

10-msec intervals).

301

Master compression motor lock detected.

 

The compression detection switch went ON while lifting the compression plate.

305

The master compression HP sensor does not switch ON within 7.5 seconds after the 

master compression motor activates to lift the compression plate.

306

The master compression HP sensor does not switch OFF within 2 seconds after the 

master compression motor activates in the compressing direction.

307

[1] The compression detection does not switch ON within 7.5 seconds after the master 

compression motor activates in the compressing direction.  (Within 5 seconds if 

moving to the Protect position.).

 

 

[2] The master compression FG sesnor does not count 20 pulses even after the 

master compression motor rotated in the compressing direction for 800ms.

309

The FG count value does not change when the master compression motor applies 

a force to begin the compression, after moving away from the home position sensor. 

(The master compression motor FG sensor status does not change.)

316

Master disposal motor lock detected.

 

The master disposal motor FG count reduced to half the value from the set speed.

Error type

T64 [Inking motor lock]   (Drum No.2)

Panel display

T64-*** 

!!System Error!! 

Press Reset Key 

If Recovery has Failed, Call Service

Error reset 

method

Press the Reset key or switch power OFF, then ON.

Error point

Error detecting condition

539

Inking motor lock detected.

 

The inking motor FG sensor does not change status within 20 ms after the inking 

motor switches ON.

Summary of Contents for MZ1070























































































































































Reviews:

No comments