manualshive.com logo in svg

Rigol MSO5000 Series, User Manual

Share
Download
Rigol MSO5000 Series User Manual Download Page 352

RIGOL

 

Chapter 21 Troubleshooting

 

21-2

 

MSO5000 User's Guide 

6.

 

The touch functions cannot be used normally. 

(1)

 

Check whether you have enabled the touch screen. If not, please press the 
touch screen switch key 

Touch Lock

 to enable the touch screen function. 

(2)

 

Check whether the screen or your finger is stained with oil or sweat. If yes, 

please clean the screen or dry your hands. 

(3)

 

Check whether there is a strong magnetic field around the instrument. If 

the instrument is close to the strong magnetic field (e.g. a magnet), please 

move the instrument away from the magnet field. 

(4)

 

If the problem still persists, please contact 

RIGOL

. 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for MSO5000 Series







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands