Rigol MSO5000 Series User Manual Download Page 12

Page: 12 / 358

RIGOL

MSO5000 User's Guide

Document Overview

Main Topics of this Manual:

Chapter 1 Quick Start

Introduces the preparations before using the oscilloscope and provides a basic

introduction of the instrument.

Chapter 2

To Set the Vertical System

Introduces the vertical system functions of the oscilloscope.

Chapter 3

To Set the Horizontal System

Introduces the horizontal system functions of the oscilloscope.

Chapter 4

To Set the Sample System

Introduces the sample system functions of the oscilloscope.

Chapter 5 To Trigger the Oscilloscope

Introduces the trigger mode, trigger coupling, trigger holdoff, external trigger, and

various trigger types of the oscilloscope.

Chapter 6

Operations and Measurements

Introduces how to make math operation, auto measurement, and cursor

measurement.

Chapter 7 Digital Voltmeter (DVM) and Frequency Counter

Introduces how to use the digital voltmeter and the frequency counter.

Chapter 8 Power Analysis (Option)

Introduces the power quality and output ripple noise of the input power.

Chapter 9 Histogram Analysis

Introduces the histogram analysis function.

Chapter 10 Digital Channel

Introduces how to use the digital channels of the mixed signal digital oscilloscope.

Chapter 11 Protocol Decoding

Introduces how to decode the input signal by using those common protocols.

Chapter 12 Reference Waveform

Introduces how to compare the input waveform with the reference waveform.

Chapter 13 Pass/Fail Test

Introduces how to monitor the input signal by using the Pass/Fail test.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for MSO5000 Series







































































































































































































































































































































































Search results

Summary of Contents for MSO5000 Series

Reviews:

Brands by name

Popular brands

Rigol MSO5000 Series, User Manual

Search results

Summary of Contents for MSO5000 Series

Reviews:

Brands by name

Popular brands