Rigol MSO5000 Series User Manual Download Page 343

Page: 343 / 358

Chapter 20 Remote Control

RIGOL

MSO5000 User's Guide

20-1

Chapter 20

Remote Control

The oscilloscope can be remotely controlled in the following three methods:

User-defined programming

You can program and control the oscilloscope by using the SCPI (Standard

Commands for Programmable Instruments) commands. For details about the

relevant commands and programming, refer to

MSO5000 Series Programming Guide

PC software

You can use the PC software to send commands to control the oscilloscope remotely.

RIGOL

Ultra Sigma is recommended. You can download the software from

RIGOL

official website (www.rigol.com).

Operation Procedures:

(1)

Set up communication between the instrument and PC.

(2)

Run Ultra Sigma and search for the instrument resource.

(3)

Open the remote command control panel to send commands.

Web Control

MSO5000 series digital oscilloscope supports Web Control. When the instrument is

connected to the internet, Web Control can display the waveform interface of the

oscilloscope in a real-time manner. You can migrate the instrument control and

waveform analysis to the control terminals (e.g. PC, mobile, and iPad) through Web

Control to realize remote control of the instrument. When you log in to the Web

Control for the first time, use the user name "admin" (without quotation marks) and

the password "rigol" (without quotation marks).

The oscilloscope can communicate with the PC via the following interfaces:



Remote Control via USB



Remote Control via LAN



Remote Control via GPIB

This chapter will illustrate how to use

RIGOL

's Ultra Sigma software to remotely

control the oscilloscope via various interfaces.

CAUTION

Before setting up communication, please turn off the instrument to avoid

causing damage to the communication interfaces.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for MSO5000 Series







































































































































































































































































































































































Search results

Summary of Contents for MSO5000 Series

Reviews:

Brands by name

Popular brands

Rigol MSO5000 Series, User Manual

Search results

Summary of Contents for MSO5000 Series

Reviews:

Brands by name

Popular brands