Rigol MSO5000 Series User Manual Download Page 326

Page: 326 / 358

RIGOL

Chapter 19 System Utility Function Setting

19-2

MSO5000 User's Guide

Remote Interface Configuration

MSO5000 series can communicate with the PC via the USB, LAN, or GPIB (requiring

to work with

RIGOL

's USB-GPIB interface converter) interface. Before using the

remote interfaces, configure the corresponding interface according to the

introductions in the following section.

LAN Configuration

Before using the LAN bus, use a network cable to connect the oscilloscope to your

local area network. The network interface of the oscilloscope is on the rear panel.

Press

Utility



LAN

to open the LAN Settings interface, as shown in the

following figure. You can view the current network settings and configure the

network parameters.

Figure 19-1 Network Connection Setting Interface

Network Status

Different prompts will be displayed according to the current network connection

status.



Network Config Succeeded!



Acquiring IP...



IP Conflict!



Disconnected!



DHCP Config Failed!



Read Status Fail!



Connected!

Network Status
Current IP Config.
Type
MAC Address
VISA Descriptor

IP Config. Type

Network Parameters

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for MSO5000 Series







































































































































































































































































































































































Search results

Summary of Contents for MSO5000 Series

Reviews:

Brands by name

Popular brands

Rigol MSO5000 Series, User Manual

Search results

Summary of Contents for MSO5000 Series

Reviews:

Brands by name

Popular brands