background image

5/10/99                                               SMA0001A.PDF         1-30

From Leveling Controller (Closest to Compressor)

Wire Color Function At Rest In Action

1 Yellow 14g Send power to Compressor to

operate and to Diode pack which
opens Right and Left Air Bag
Valves

Continuity to
ground

12 Volts positive

2 Brown Opens The Vent Valve and

sends power to Diode pack
which opens Right and Left Air
Bag Valves

Continuity to
ground

12 Volts positive

3 Orange Detects air pressure in the bags

from 0-25 PSI

0-25 PSI
continuity to
ground

Above 25 PSI no
continuity to
ground

4 Brown/Yellow Detects air pressure in the bags

from 0-40 PSI

0-40 PSI no
continuity to
ground

40 PSI and
higher, continuity
to ground

To Air Valve Assembly

Wire Color Function At Rest In Action

1 Yellow/Black Opens the Right and Left Air

Bag Valve to fill the bags and to
empty the bags

Continuity to
ground

12 Volts positive
to fill air bags
and to drain bags

2 Brown Opens the Vent Valve to drain

the bags

Continuity to
ground

12 Volts positive
to drain air bags

3 Orange Detects air pressure in the bags

from 0-25 PSI

0-25 PSI
continuity to
ground

Above 25 PSI no
continuity to
ground

4 Brown/Yellow Detects air pressure in the bags

from 0-40 PSI

0-40 PSI no
continuity to
ground

40 PSI and
higher, continuity
to ground

Summary of Contents for Activan













































Reviews: