background image

Revision 2 

Optional Accessories Available: 

 
 
Additional Remotes (GTR179)

: Spare/Additional remotes for the automatic gate kit, 

these will need to be paired to the motor. 

 
Infrared Photocells (GTR208)

: Detects pedestrians, vehicles and objects that cross 

an infrared beam and prevents the gate from closing. 

 
Exit Wand (GTR147)

: Senses cars or trucks moving at more than 8km per hour and 

opens the gate without the need for using a remote or keypad. 
 

Wireless Keypad (GTR180)

: Allows secure access through the gate used with a user 

set code. 
 

Hard Wire Keypad (GTR055)

: Allows secure access through the gate used with a 

user set code. 
 

External Remote Receiver (GTR197)

: Allows the pairing of extra remotes. Pair up to 

250 remotes to your gate opener with this accessory. 
 

Hardwire Push Button (GTR202)

: Open your gate at the push of a button. 

 
Wireless Push Button (GTR201)

: Wirelessly open your gate at the push of a button. 

 

Warning Light (GTR198)

: Alerts people near the gate and users that the gate is in 

operation. 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for GTR212






























Reviews: