background image

SpaceLogger

®

.S10

 

User Manual 

 

©2012-13 Richard Paul Russell Limited, New Harbour Building, Bath Road, Lymington SO41 3SE United Kingdom 

 Tel +44 (0) 1590 679755 Fax +44 (0) 1590 688577 e-mail [email protected] web www.r-p-r.co.uk 

 

 

 

- 31 -

 

017SL167/3 04/09/13 

A3

 

Guarantee 

 
System  components  are  warranted  for  a  period  of  twelve  (12)  months  from  the  original  date  of 
purchase,  against  defective  materials  and  workmanship.    In  the  event  that  warranty  service  is 
required, please contact Richard Paul Russell Ltd. 
 
This warranty is only valid if, when warranty service is required, a full description of the fault is 
provided and presented with the original invoice, and the serial number(s) on the component has 
not been defaced. 
 
Richard  Paul  Russell  Ltd’s  liability  is  limited  to  items  of  its  own  manufacture,  and  it  does  not 
accept  liability  for any loss  resulting from  the operation or interpretation of the results from  this 
equipment. 
 
This warranty covers none of the following: 
 

 

Periodic check ups, maintenance and repair or replacement of parts due to normal wear and 
tear. 

 

Cost relating to transport, removal, or installation of the component. 

 

Misuse,  including  failure  to  use  the  component  for  its  normal  purpose  or  incorrect 
installation. 

 

Damage  caused  by  Lightning,  Water,  Fire,  Acts  of  God,  War,  Public  Disturbances, 
incorrect supply voltage or any other cause beyond the control of Richard Paul Russell Ltd. 

 

Units which have been repaired or units altered by a party other than Richard Paul Russell 
Ltd’s employees or agents without prior written consent from Richard Paul Russell Ltd. 

 
In  no  event  shall  Richard  Paul  Russell  Ltd  be  liable  under  any  circumstances  for  any  direct, 
indirect  or  consequential  damages,  any  financial  loss  or  any  lost  data  contained  in  any  product 
(including  any  returned  product),  regardless  of  the  cause  of  loss.    Richard  Paul  Russell  Ltd 
products are not  warranted to operate without failure.   Richard Paul Russell Ltd’s  products must 
not be used in life support systems or other application where failure could threaten injury or life. 
 
The  Customers  statutory  rights  are  not  affected  by  this  warranty.    Unless  there  is  national 
legislation to the contrary, the rights under this warranty are the customer’s sole rights and Richard 
Paul  Russell  Ltd  shall  not  be  liable  for  indirect  or  consequential  loss  or  damage  to  any  other 
related equipment or material. 
 
 

 

Summary of Contents for SpaceLogger.S10



































Reviews: