Regency HZ33CE-LP Owners & Installation Manual Download Page 49

Page: 49 / 60

Regency HZ33CE Gas Fireplace

INSTALLATION

If installing the optional mantel ensure the combustible and
non combustible material around the unit are installed fl ush
with the unit. (See Diagram 1 below).
The mantel cannot be installed if materials are not fl ush.

. Install 2 middle screws on unit face - do not tighten. Slide

bracket over screws then tighten, install 2 outer screws .

Install four (4) wood screws, two (2) on each side of the
bracket into the wall studs as shown below.

Diagram 1- Materials fl ush w/unit.

Diagram 2 -Bracket screw locations on unit.

Diagram 3 -Bracket screw locations into stud.

Diagram 6 -Final Install

Lift up mantel and line up the middle rib on backside of faceplate with

middle indent on bracket. This will centre the faceplate and allow 1/16"
adjustment from side to side.

Line up fl ange on hearth portion of mantel, with opening between bracket
and unit.

Repeat steps 1 and 2 to install lower bracket - screw locations are shown

below.

Install middle 2 screws on

to unit fi rst

OPTIONAL MANTEL INSTALLATION

Combustible
Material

Non-combustible Material (3-1/2" x 36")

Nailing Strip -1/2" back from unit face

Combustible
Material

Summary of Contents for HZ33CE-LP





























































Search results

Summary of Contents for HZ33CE-LP

Reviews:

Related manuals for HZ33CE-LP

Brands by name

Popular brands

Regency HZ33CE-LP, Owners & Installation Manual

Search results

Summary of Contents for HZ33CE-LP

Reviews:

Related manuals for HZ33CE-LP

Brands by name

Popular brands