Regency HZ33CE-LP Owners & Installation Manual Download Page 43 | Manualshive

Page: 43 / 60

background image

Regency HZ33CE Gas Fireplace

43

INSTALLATION

GLASS CRYSTALS AND OPTIONAL STONES

INSTALLATION ON BURNER AND FIREBOX FLOOR

Glass Crystals shown on Burner and Firebox Floor

BURNER PACKAGES

Unit

*Glass Crystals

**Spa Stones

Ceramic Stones

Volcanic Stones

HZ33CE

4 lb

4 lb glass + 70 spa stones

4 lb glass + 24 stones

4 lb glass + 30 stones

NOTE:

*

Glass Crystals are available in 1lb and 5lb bags.

** Spa stone package contains 70 stones

Evenly spread the Glass Crystals or optional Ceramic Spa Stones over the burner.
Ensure the crystals (or stones) do not overlap too much as this will effect the fl ame pattern.

IMPORTANT NOTE:

Only the supplied approved Glass Crystals and Stones are to be used with these fi replaces. Use of any other type of glass crystals or stones can
alter the unit's performance, any damage caused by the use of any unapproved glass or stones will not be covered under warranty.

When using Ceramic Spa Stones

DO NOT

cover burner ports or pilot light that lead to pilot fl ame. Ensure the crystals or stones do not overlap

excessively as this will effect the fl ame pattern.

1) Start installing Crystals on back of

Burner and Firebox Floor

2) Distribute Crystals evenly towards

front of Burner and Firebox Floor

3) Work Crystals from back to front

edge of Firebox Floor

4)

Spread

Crystals

evenly over the

burner and fi rebox base

5) Ensure Crystals DO NOT block the

front of the pilot hood and fl ame to

light the burner

OPTIONAL SPA STONES INSTALLATION (AROUND BURNER

)

NOTE:

Spa stones are

NOT

to be placed anywhere on the burner tube or Pilot assembly area.

NOTE: Correct fi nal glass installation of Crystals shown
in step 4 and 5.
The Burner and Firebox Floor should not be visible
when the fl ame is out.

«
...
41
42
43
44
45
...
»

Summary of Contents for HZ33CE-LP





























































Reviews:

No comments

Related manuals for HZ33CE-LP

Brand: Desa Pages: 44

Brand: FireplaceXtrordinair Pages: 38

Grandville GVF36-2P

Brand: Napoleon Pages: 28

Brand: Travis Industries Pages: 8

Brand: Napoleon Pages: 60

Brand: QOMOTOP Pages: 10

Brand: Paloform Pages: 14

Brand: Empire Comfort Systems Pages: 28

Brand: Valor Pages: 19

Brand: M Design Pages: 2

Brand: Solution FIres Pages: 24

Brand: Heat & Glo Pages: 2

BRAZI GFT22001-ACCGC

Brand: EAST OAK Pages: 2

Mercer CM140-095

Brand: Charmate Pages: 4

Brand: ELEMENTI Pages: 20

Brand: Napoleon Pages: 24

Brand: IHP Pages: 2

Brand: Element4 Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands