Regency HZ33CE-LP Owners & Installation Manual Download Page 31

Page: 31 / 60

Regency HZ33CE Gas Fireplace

INSTALLATION

CONVERSION KIT# 434-972 FROM NG TO LP

For HZ33CE using SIT 886 NOVA Gas Valve

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !!

Remove regulator and discard. Install Hi/

Lo pressure regulator onto the valve with
2 screws as shown below.

Attach the label “This unit has been

converted to LPG” near or on top of the

serial # decal

10.

Replace yellow “NG” label with red

“LPG”

label

11.

Reverse steps 2 - 1.

12.

Check for gas leaks.

13.

Check inlet and outlet pressures.

14.

Check operation of fl ame control.

Installer Notice:

These instructions must be left

with the appliance

Each Kit contains one LPG
Conversion Kit # 434-972

LPG Conversion Kit Contains:
Qty. Part #

Description

904-241

Burner Orifi ce #56

918-590

Decal "Converted to

LPG"

908-528

Red "LPG" label

1 904-529

5/32"

Allen

Key

1 910-101

LPG

Injector

(Pilot

Orifi

ce)

911-009

Hi/Lo Conversion LP

1 919-126

Instruction

Sheet

Installation of the LPG
Conversion Kit:

Shut off the gas supply

a) Remove the glass door.

Remove the Glass Crystals or

Ceramic

Stones.

Also

remove

Inner Panels - if installed.

Remove the six (6) screws in locations

shown below to remove burner tray.

Unscrew the pilot orifi ce with the Allen

key and replace with the LPG pilot

orifi ce in the kit and replace pilot cap.

Remove burner orifi ce with a 1/2"
wrench and discard. Use another
wrench to hold on to the elbow below

the orifi ce.

Burner Orifi ce

Install the new burner orifi ce stamped
#56.

Pull off the pilot cap to expose the pilot

orifi ce.

Diagram 2

Diagram 3

Diagram 4

Diagram 5

Diagram 6

Diagram 1

Remove 2 screws in location shown in
below - slide burner to the right then lift
out. (See Diagram 2)

Summary of Contents for HZ33CE-LP





























































Search results

Summary of Contents for HZ33CE-LP

Reviews:

Related manuals for HZ33CE-LP

Brands by name

Popular brands

Regency HZ33CE-LP, Owners & Installation Manual

Search results

Summary of Contents for HZ33CE-LP

Reviews:

Related manuals for HZ33CE-LP

Brands by name

Popular brands