Regency HZ33CE-LP Owners & Installation Manual Download Page 48 | Manualshive

Page: 48 / 60

background image

48

Regency HZ33CE Gas Fireplace

INSTALLATION

OPTIONAL 4-SIDED FACEPLATE INSTALLATION

If installing the optional faceplate ensure the combustible
and non combustible material around the unit are installed
fl ush with the unit. (See Diagram 1 below).
The faceplate cannot be installed if materials are not fl ush.

1

. Install 2 middle screws on unit face - do not tighten. Slide

bracket over screws then tighten. Install 2 outer screws .

2.

Install four (4) wood screws, two (2) on each side of the
bracket into the wall studs as shown below.

Diagram 1- Materials fl ush w/unit.

Diagram 2 -Bracket screw locations on unit.

Diagram 3 -Bracket screw locations.

Diagram 4 -Line up faceplate and bracket.

Middle Rib on Faceplate

Diagram 6 -Final Install

Diagram 5 -Hang faceplate on bracket

3.

Line up the middle rib on backside of faceplate with middle indent on bracket.
This will centre the faceplate and allow 1/16" adjustment from side to side.

4

. Lift faceplate up and lower gently onto bracket.

Install middle 2 screws on

to unit fi rst

Combustible
Material

Non-combustible Material (3-1/2" x 36")

Nailing Strip -1/2" back from unit face

Combustible
Material

«
...
46
47
48
49
50
...
»

Summary of Contents for HZ33CE-LP





























































Reviews:

No comments

Related manuals for HZ33CE-LP

Oakville Series

Brand: Napoleon Pages: 72

Brand: Napoleon Pages: 4

Brand: Valor Pages: 12

Brand: Napoleon Pages: 48

Brand: Napoleon Pages: 4

Brand: Napoleon Pages: 20

Allure Vertical Series

Brand: Napoleon Pages: 120

Brand: Napoleon Pages: 132

Brand: Home Decorators Collection Pages: 16

CROSSOVER CO10-102

Brand: Magma Pages: 22

Brand: Rinnai Pages: 24

Brand: stellar labs Pages: 50

GOLDEN DAWN TX 93531

Brand: Leigh Country Pages: 2

Brand: Fire Sense Pages: 15

Flush Wood Plus

Brand: Travis Industries Pages: 32

Brand: Allen + Roth Pages: 40

Brand: Northline Express Pages: 35

mantels & surrounds Kenwood Flush

Brand: Fireside Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands