Regency Fireplace Products Grandview G600C-1 Owners & Installation Manual Download Page 39

Page: 39 / 100

installation

Grandview

G600C-1 Gas Fireplace

Faceplate Installation (Part # 776-922, 776-924, 776-926)

08.26.20

920-299

FACEPLATE INSTALLATION

G600EC/G600C

PART # 776-922, 776-924, 776-926

A 1/2” (13 mm) gap must be maintained on the
sides of the fireplace to allow the Face Plate to
be installed and removed.

Do NOT finish past the front face of the fireplace.

(19 mm)

Nailing Flange Tabs
folded forward

Mounting Tabs
folded forward

Mounting Tab
Folded Forward

Nailing Flange
folded forward

Framing

Face Plate

Install the faceplate by resting the arms on the
Face Plate on top of the mounting tabs.

Adjust left and right to center the Face Plate.

NOTE: Do not touch the faceplate without

clean, soft, gloves. Dirt or oils can be
transferred onto the finish and become
permanent.

Critical Finishing Gap

30-7/8"

(784 mm)

33-3/4"

(857 mm)

33"

(838 mm)

Summary of Contents for Grandview G600C-1





































































































Search results

Summary of Contents for Grandview G600C-1

Reviews:

Related manuals for Grandview G600C-1

Brands by name

Popular brands

Regency Fireplace Products Grandview G600C-1, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C-1

Reviews:

Related manuals for Grandview G600C-1

Brands by name

Popular brands