Regency Fireplace Products Grandview G600C-1 Owners & Installation Manual Download Page 43

Page: 43 / 100

installation

Grandview

G600C-1 Gas Fireplace

Conversion to Rear Vent

Note: This conversion must be done prior to the unit being

placed in position.

The unit comes equipped as a top vent unit. These instruc-

tions are to be used only if the unit is going to be rear

vented.

1. Remove the collar trim piece from the unit by removing 6 screws.

Collar trim piece

2. Remove the intake over plate from the rear by removing the top 2 screws

and loosening the bottom 2 screws.

Diagram 1

Diagram 6

Diagram 9

Diagram 2

Diagram 3

3. Remove the exhaust cover plate from the rear by removing the top 4 screws

and loosening the bottom 2 screws.

Hidden screw

Diagram 4

4. Remove the intake collar from the top by removing 4 screws.

Diagram 5

Hidden screw

5. Remove the exhaust collar from the top by removing the front 4 screws and

loosening the screws closest to the back of the unit.

Diagram 7

Diagram 8

Summary of Contents for Grandview G600C-1





































































































Search results

Summary of Contents for Grandview G600C-1

Reviews:

Related manuals for Grandview G600C-1

Brands by name

Popular brands

Regency Fireplace Products Grandview G600C-1, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C-1

Reviews:

Related manuals for Grandview G600C-1

Brands by name

Popular brands