Regency Fireplace Products Grandview G600C-1 Owners & Installation Manual Download Page 6

Page: 6 / 100

Grandview

G600C Gas Fireplace

safety decal

This is a copy of the label that accompanies each Grandview™ G600 Direct Vent Gas Fireplace. We have printed a copy of the contents here for your review.

NOTE:

Regency

units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.

For the State of Massachusetts, installation and
repair must be done by a plumber or gas fitter
licensed in the Commonwealth of Massachusetts.

For the State of Massachusetts, flexible connectors
shall not exceed 36 inches in length.

For the State of Massachusetts, the appliances
individual manual shut-off must be a t-handle
type valve.

The State of Massachusetts requires the
installation of a carbon monoxide alarm in
accordance with NFPA 720 and a CO alarm with
battery back up in the same room where the gas
appliance is installed.

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and Propane Installation Code, CSA B149.1.

This appliance must be installed in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the

United States, or when such a standard is not applicable, ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard or ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles

This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured (mobile) home where not prohibited by local codes. See

owner's manual for details. This appliance is not convertible for use with other gases, unless a certified kit is used. (Kit #776-969). Fan Part # 761-917.

Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation ANSI Z223.1, National Fuel Gas Code ou CSA-B149.1 en vigueur. Installer l'appareil

selon la norme CAN/CSA-Z240, Série MM, Maison mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24 CFR Part 3280, Manufactured Home Construction and Safety Standard. Si ces normes

ne sont pas pertinentes, utilisez la norme ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard, ou ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles.

Cet appareil doit être utilisé uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison préfabriquée ou mobile (É.-U. seulement) installée à demeure

si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certifiée est

fournie.

This vented gas fireplace heater is not for use with air filters. Ne pas utiliser de filtre à air avec ce foyer au gaz à évacuation.

FOR USE WITH GLASS DOORS CERTIFIED WITH THE APPLIANCE ONLY

POUR UTILISATION UNIQUEMENT AVEC LES PORTES EN VERRE CERTIFIÉES AVEC

L'APPAREIL

For Use Only with Barrier (Part # 776-109/P)

Utiliser uniquement avec l’écran ( n ° 776-109/P)

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE

562

DOOR SEAL: Please

check that the door is

properly sealed

FPI Fireplace Products International Ltd. Delta, BC, Canada

Minimum Clearances to Combustibles / Rear Vent—Clean Finish

Dégagements minimaux par rapport aux matériaux combustibles

Serial No./ No de série

920-418a

Electrical supply/Alimentation électrique 115VAC, 1.5A, 60Hz. CATEGORY/CATÉGORIE 1

NOT FOR USE WITH SOLID FUELS /

NE PAS UTILISER AVEC UN COMBUSTIBLE SOLIDE

Made in Canada/ Fabriqué au Canada

Duplicate S/N

(

See Instruction Manual for detailed instructions)

APPAREIL

FONCTIONNANT AU GAZ PROPANE

Modèle

-LP1

G600C

PROPANE GAS: Model G600C-LP1

NATURAL GAS: Model G600C-NG1

Minimum supply pressure

Manifold pressure high

Manifold pressure low

Orifice size

Minimum input

Maximum input

Altitude

Pression d'alimentation minimale

Pression manifold - haute

Pression manifold - basse

Taille de l'orifice

D bit calorifique minimal

D bit calorifique maximal

Altitude

5.0" WC/C.E. (1.25 kPa)

3.8" WC/C.E. (0.94 kPa)

1.1" WC/C.E. (0.27 kPa)

#44 DMS

11,500 Btu/h

3.37 kWh

21,000 Btu/h

6.15 kWh

0-4500 ft/pi

(0-1372 m)

Part #: 920-418a

Colour: Everything black on grey except what is highlighted is printed red.

Size: File@100% 9.117’’W x 6.045’’H

Aug 27/21: Created Draft

Dec. 22/21: Updated DMS #

Printer

:Start serial sequence @ 000001

Pression d'alimentation minimale

Pression manifold - haute

Pression manifold - basse

Taille de l'orifice

D bit calorifique minimal

D bit calorifique maximal

Altitude

11" WC/C.E. (2.74 kPa)

10.5"

WC/C.E. ( 2.61 kPa)

2.9"

WC/C.E. (0.72 kPa)

#55 DMS

11,000 Btu/h

3.22 kWh

20,500 B tu/h 6.01 kWh

0-4500 ft/pi

(0-1372 m)

Minimum supply pressure

Manifold pressure high

Manifold pressure low

Orifice size

Minimum input

Maximum input

Altitude

C #: 4001172

MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE

Listed/Nom:

Vented Gas Fireplace Heater / Foyer au Gaz à Évacuation

Certified to/Certifi pour:

ANSI Z21.88:19 • CSA 2.33:19

CSA 2.17-2017

Refer to Intertek's Directory of Building Products for detailed information.

Pour plus de détails , se reporter au Répertoire des produits de construction de Intertek.

APPAREIL

FONCTIONNANT AU GAZ NATUREL

Modèle G600C-NG1

CSA P.4.1 Fireplace Efficiency (FE) /Efficacité énergétique des foyers (EEF) CSA P.4.1

Natural Gas / Gaz naturel: 64.79%

Propane Gas / Gaz propane: 66.76%

0" Clearance to combustibles from

Top, sides, and bottom of unit

0.5” Clearance to combustibles from

rear of unit

Mantel Clearances from

Fireplace Opening /

(A) 12” (305 mm) at max. depth

Side Wall Clearance from Fireplace

Opening /

B) Min 6” (152 mm)

Ceiling from Top of Fireplace

Opening:

C) Min. 44.25” (1124 mm)

Mantel Depth:

D) Max. 12” (305 mm)

Alcove Clearances:

E) Min. Width 84” (2134 mm)

F) Max. Depth 36” (914 mm)

Minimum Vent Clearances:

Horizontal Top 2” (51 mm)

Horizontal Side 1-1/2” (38 mm)

Horizontal Bottom 1-1/2” (38 mm)

Vertical Vent 1-1/2” (38 mm)

Part No. 946-556 HeatWave Kit may be used. La trousse HeatWave (pièce no. 946-556) peut être utilisée.

CANADIAN ENERGY

PERFORMANCE

VERIFIED

RENDEMENT

ÉNERGÉTIQUE

VÉRIFIÉ

EP5011169

Copy of Safety Decal

Decal Location

DO NOT REMOVE DECAL FROM UNIT.

Remove bottom cover—decal will
be on the floor of the unit

Summary of Contents for Grandview G600C-1





































































































Search results

Summary of Contents for Grandview G600C-1

Reviews:

Related manuals for Grandview G600C-1

Brands by name

Popular brands

Regency Fireplace Products Grandview G600C-1, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C-1

Reviews:

Related manuals for Grandview G600C-1

Brands by name

Popular brands