manualshive.com logo in svg

Regency Fireplace Products Grandview G600C-1, Owners & Installation Manual

The Regency Fireplace Products Grandview G600C-1 Owners & Installation Manual is a comprehensive guide to help you set up and operate your fireplace effortlessly. This essential manual can be downloaded for free from our website, ensuring you have the necessary instructions at your fingertips.

Share
Download
background image

18   

|    

Grandview

®

 G600C-1 Gas Fireplace

 

installation

Clearance / Framing and Venting Configurations

The G600C-1 is designed to allow for unique installation options—depending on the desired finish.  
Please review the options and follow the specific clearance, framing, and finishing options for that application.

The applications are as follows:

Cool Wall Installation-Clean Front & Outside Finish

: combustible materials can be installed right up to the fireplace opening with this option.

Non Combustible Installation-Clean Front & Outside Finish Applications:

 non-combustible required when installing materials right to the fireplace 

opening with this option.

See descriptive diagrams on the next page.

Note: The topics listed below can be found in the pages that follow.

Clearance / Framing and Venting Configurations ..................................................................................................................................... 18

Cool Wall Installation (Combustible Finishing) .......................................................................................................................................... 19

Non-Combustible Installation .................................................................................................................................................................... 19

Unit Assembly Prior to Installation (Nailing Flange Installation) ............................................................................................................... 20

Nailing Flange Installation ........................................................................................................................................................................ 21

Cool Wall Clearances ............................................................................................................................................................................... 23

Cool Wall Mantel Clearances ................................................................................................................................................................... 24

Cool Wall Mantel Leg Clearances ............................................................................................................................................................ 24

Cool Wall Installation—Framing ................................................................................................................................................................ 25

Cool Wall Installation-Cool Wall Conversion ............................................................................................................................................. 26

Chase Venting .......................................................................................................................................................................................... 27

Chase Enclosure (Cool Wall) .................................................................................................................................................................... 28

Chase Vent Installation - Cool Wall (Part #776-941)................................................................................................................................. 29

Clean Front Installation (Non Cool Wall) - Clearances ............................................................................................................................. 30

Clean Front Installation (Non Cool Wall) - Mantel Clearances ................................................................................................................. 31

Clean Front Installation (Non Cool Wall) - Mantel Leg Clearances .......................................................................................................... 32

Clean Front Installation (Non Cool Wall)—Non Combustible 

  Requirements ......................................................................................................................................................................................... 32

Clean Front Installation—Framing (Non Cool Wall) .................................................................................................................................. 33

Clean Front Installation ............................................................................................................................................................................. 34

Outside Finish Installation (Non Cool Wall)—Clearances......................................................................................................................... 35

Outside Finish Installation (Non Cool Wall) - Mantel Clearances ............................................................................................................. 36

Outside Finish Installation (Non Cool Wall)—Mantel Leg 

  Clearances ............................................................................................................................................................................................. 36

Outside Finish Installation (Non Cool Wall)—Framing .............................................................................................................................. 37

Outside Finish—Finishing  ........................................................................................................................................................................ 38

Faceplate Installation (Part # 776-922, 776-924, 776-926) ...................................................................................................................... 39

Finishing Trim Install (Part # 776-928) ...................................................................................................................................................... 40

Wall Board/Drywall Installation ................................................................................................................................................................. 42

Conversion to Rear Vent ........................................................................................................................................................................... 43

Vent Restrictor Installation (Part # 776-027) ............................................................................................................................................. 46

Summary of Contents for Grandview G600C-1





































































































Reviews:

No comments

Related manuals for Grandview G600C-1

J. A. Roby ATHOS Owner'S Manual preview
ATHOS
Brand: J. A. Roby Pages: 4
HAMPTONBAY 23WM9083-PT85 Use And Care Manual preview
23WM9083-PT85
Brand: HAMPTONBAY Pages: 30
Majestic 360DVS2 Installation Instructions & Homeowner'S Manual preview
360DVS2
Brand: Majestic Pages: 40
Empire Comfort Systems VFP32FB0F-5 Installation Instructions And Owner'S Manual preview
VFP32FB0F-5
Brand: Empire Comfort Systems Pages: 13
Calflame FRP-906-1 Owner'S Manual preview
FRP-906-1
Brand: Calflame Pages: 35
iKayaa JS-FT039K Manual preview
JS-FT039K
Brand: iKayaa Pages: 2
Desa Comfort Glow CGEFP33PR Owner'S Operation And Installation Manual preview
Comfort Glow CGEFP33PR
Brand: Desa Pages: 38
Monessen Hearth ACUF32-BD Installation Manual preview
ACUF32-BD
Brand: Monessen Hearth Pages: 24
ELEMENTI OFG105NG Owner'S Manual preview
OFG105NG
Brand: ELEMENTI Pages: 20
Wamsler 108 30 OPHIT User Instruction preview
108 30 OPHIT
Brand: Wamsler Pages: 96
Napoleon Luminex Series Installation And Operation Manual preview
Luminex Series
Brand: Napoleon Pages: 80
Napoleon Astound-Built In Series Installation And Operation Manual preview
Astound-Built In Series
Brand: Napoleon Pages: 80
Charmate Mercer CM140-095 Quick Start Manual preview
Mercer CM140-095
Brand: Charmate Pages: 4
IHP RHAPSODY RHAP42N Installation Instructions Manual preview
RHAPSODY RHAP42N
Brand: IHP Pages: 6
Valor LEGEND G4 780JN (NG) Installation And Owner'S Manual preview
LEGEND G4 780JN (NG)
Brand: Valor Pages: 46
KASTOR TS-12 Installation And Operating Instructions Manual preview
TS-12
Brand: KASTOR Pages: 44
CMC Masonry Fireplace Enclosure Installation & Operation Instructions preview
Masonry Fireplace Enclosure
Brand: CMC Pages: 4
Majestic fireplaces MR42A Installation Manual preview
MR42A
Brand: Majestic fireplaces Pages: 18

Brands by name

Popular brands

Load more brands