Regency Fireplace Products Grandview G600C-1 Owners & Installation Manual Download Page 34

Page: 34 / 100

Grandview

G600C-1 Gas Fireplace

installation

Clean Front Installation

08.14.20

920-302-fr

CLEAN FRONT TRIM INSTALLATION

G600C/G600EC

max.

Diagram 2: Finishing Dimensions

Diagram 1: Exploded View

NOTE: Do NOT finish beyond the
dimensions in Diagram 2.

26-3/4"

(679 mm)

28-3/4"

(730 mm)

(51 mm) max.

Pièce No

. 776-929

1. Install the nailing flanges, see manual

for instructions.

2. Loosen the four (4) screws that secure

the left and right nailing flanges to the
unit.

3. Slide the left and right tiling flanges onto

the front of the fireplace. Use the slots
to center, with the screw securing the
nailing flanges (Diagram 1).

4. Tighten screws.

5. Slide the bottom tiling flange against

the bottom of the fireplace. Secure with
a screw on each side.

6. Finishing material can now be pressed

against the flat edge created by the
clean front trim (Diagram 2).

CLEAN FRONT TRIM INSTALL
INSTRUCTIONS:

Summary of Contents for Grandview G600C-1





































































































Search results

Summary of Contents for Grandview G600C-1

Reviews:

Related manuals for Grandview G600C-1

Brands by name

Popular brands

Regency Fireplace Products Grandview G600C-1, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C-1

Reviews:

Related manuals for Grandview G600C-1

Brands by name

Popular brands