background image

01-02

1

28881 Rev G

NOVUS™ SERIES

REAR DIRECT VENT GAS APPLIANCE

INSTALLATION  &  OPERATING

INSTRUCTIONS

WARNING!

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual. For

assistance or additional information, consult a qualified installer, service agency or the gas supplier.

WARNING:  If  the  information  in  this

manual is not followed exactly, a fire

or explosion may result causing prop-

erty damage, personal injury or loss of

life.

— Do not store or use gasoline or other

flammable  vapors  and  liquids  in  the

vicinity of this or any other appliance.

— What to do if you smell gas

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Immediately  call  your  gas  supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the fire department.

— Installation  and  service  must  be

performed  by  a  qualified  installer,

service agency or the gas supplier.

33” & 36” with the X Burn System

For Residential Use - Meets All HUD Requirements for

Manufactured  Housing  Installations

U.S. Patent 5,613,487

Read these installation instructions completely before

beginning installation. Failure to follow them could cause

an appliance malfunction resulting in serious injury and/

or property damage.

CAUTION:

Do not expose the appliance to the elements (such as rain, etc.)

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for NOVUS series

































Reviews: