Redline RDL-3000 SC Installation Manuallines Download Page 4

Page: 4 / 65

RDL-3000

INSTALLATION GUIDELINES

70-00159-01-06

Page

of 65

kune 12, 2012

5.1

General Guidelines .......................................................................................... 26

5.1.1

Grounding ....................................................................................................... 26

5.1.2

Surge Protection ............................................................................................. 27

5.1.3

Protecting Cables from Abrasion and Temperature ......................................... 28

5.1.4

Ethernet Cable Drip-Loop ............................................................................... 29

5.2

Mounting Kits ................................................................................................... 30

5.2.1

Lightweight Mounting Kit ................................................................................. 30

5.2.2

Heavy-Duty Mounting Kit ................................................................................ 33

5.3

RF Ports ............................................................................................................ 36

5.3.1

RF Cable Connections .................................................................................... 36

5.3.2

Weatherproofing RF Ports............................................................................... 36

5.4

Ethernet Port .................................................................................................... 39

5.4.1

Ethernet Cable Connections ........................................................................... 39

Assembling the Ethernet Weatheproof Connector ........................................ 39

Disconnecting the Ethernet Cable ................................................................ 40

Weatherproofing the Ethernet Port ............................................................... 41

5.4.2

Ethernet Surge Protection ............................................................................... 42

Installing the Ethernet Line Protector (LP) Unit ............................................. 42

Installing the LP Mast Mount Kit ................................................................... 44

Weatherproofing the LP Ports ...................................................................... 45

5.4.3

Indoor PoE ...................................................................................................... 46

5.5

Configuration ................................................................................................... 47

5.5.1

Step 1: Login to RDL-3000 .............................................................................. 47

Telnet Access .............................................................................................. 48

Web Browser ............................................................................................... 48

5.5.2

Step 2: Restore Default Settings ..................................................................... 48

Factory Reset ............................................................................................... 48

Long Reset ................................................................................................... 49

5.5.3

Step 3: Install Options Key .............................................................................. 49

Operation with No Options Key .................................................................... 49

Enter Permanent Options Key ...................................................................... 49

5.5.4

Step 4: Required Wireless Settings ................................................................. 50

RF Power Settings ....................................................................................... 51

5.5.5

Step 5: Create and Enable a Wireless Link ..................................................... 53

Add a Subscriber Link .................................................................................. 53

Add a Service Group .................................................................................... 53

Add a Service ............................................................................................... 54

5.6

Antenna Alignment .......................................................................................... 55

5.6.1

Coarse Antenna Alignment ............................................................................. 55

Azimuth Alignment ....................................................................................... 55

Elevation Alignment ..................................................................................... 55

5.6.2

Antenna Medium Adjustment Using the Audible Adjustment Tool ................... 56

5.6.3

Antenna Fine Alignment Using RSSI and SINADR ......................................... 56

Subscriber Link Status Screen (Subscriber Only) ......................................... 57

Using the Web Alignment Tool (SS Only) ..................................................... 57

Summary of Contents for RDL-3000 SC


































































Search results

Summary of Contents for RDL-3000 SC

Reviews:

Related manuals for RDL-3000 SC

Brands by name

Popular brands

Redline RDL-3000 SC, Installation Manuallines

Search results

Summary of Contents for RDL-3000 SC

Reviews:

Related manuals for RDL-3000 SC

Brands by name

Popular brands