Redline RDL-3000 SC Installation Manuallines Download Page 20 | Manualshive

Page: 20 / 65

background image

RDL-3000

INSTALLATION GUIDELINES

70-00159-01-06

Proprietary Redline Communications © 2012

Page

20

of 65

kune 12, 2012

Web Browser (HTTP)

To monitor and configure the RDL-3000 using HTTP, open a Web browser (Internet
Explorer 6 or higher recommended) and enter the unit IP address. For new systems, the
default IP address is 192.168.25.2. The following login dialog should be displayed:

Figure 7: Features - Web Login to the RDL-3000

The default username is 'admin' and the default password is 'admin'.

Note: There is no logout command on the Web interface.

Audible Alignment Tool

The audible alignment tool is provided to assist the installer to perform basic antenna
alignment. When enabled, the audible alignment signal 'chirps' slowly when a low signal
level is detected, and faster when stronger signals are detected. Use the Web or CLI
interface to enable and disable the tool.

3.5

Mounting Kits

Lightweight Mounting Kit

Lightweight mounting kit includes mounting bracket with assembly hardware. Fits 25-105
mm (1.0-4.25 in) mast pipe or mounts on a flat surface. Two 230 mm (9 in) RF jumper
cables (N-type connectors, 50 Ohm)

are included with each mounting kit.

Heavy-Duty Mounting Kit

Heavy-duty mounting kit includes mounting bracket with assembly hardware. Fits 45-110
mm (1.75-4.5 in) mast. Two 400 mm (16 in) RF jumper cables (N-type connectors, 50
Ohm)

are included with each mounting kit.

3.6

Grounding

Ground Lug

A ground-lug

is provided on the RDL-3000 chassis. Use this connection to terminate

a grounding wire. All RDL-3000 systems must be properly grounded to protect against
power surges and accumulated static electricity.

«
...
18
19
20
21
22
...
»

Summary of Contents for RDL-3000 SC


































































Reviews:

No comments

Related manuals for RDL-3000 SC

Brand: Panasonic Pages: 443

Brand: Can-Am Pages: 16

Brand: Xerox Pages: 2

Brand: Antec Pages: 5

Brand: ipf electronic Pages: 4

Instrument Control System

Brand: Opus-Two Pages: 8

Zeus F745-VTX STACK

Brand: HGLRC Pages: 19

Brand: Katranji Pages: 2

Brand: Metra Electronics Pages: 2

00.15189.002 050

Brand: Lambrecht Pages: 10

Easyrack 6622520 01 01

Brand: hepco & becker Pages: 4

Brand: PullRite Pages: 10

Brand: Viking Pages: 1

Brand: Crivit Pages: 70

37-Key Audio/MIDI Interface and Controller Ozonic

Brand: M-Audio Pages: 38

Brand: Nav TV Pages: 3

Brand: Mystic Romance Pages: 10

ACCS 616810-BOX-BS

Brand: iQunet Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands