background image

BATTERY STORAGE AND HANDLING

WARNING:  

Failure   to   read,   understand,   and  

follow these instructions may result in overheating, 
chemical leakage, smoke emission, fire, or other 
potentially harmful results.

Always follow proper battery handling and storage practices. Improper 
handling and/or  failure  to abide  by proper  storage  instructions may 
cause   permanent  damage   to   batteries,   or   degrade   battery  charge  
holding capacity. Improper handling practices or failure to comply with 
instructions may also put you at risk.

Lithium-Ion batteries, like the REDVOLT

®

, REDVOLT-V™, REDVOLT 

XL, and RED BRICK

®

, self-discharge over time. When storing for long 

periods of time, store batteries separately from the camera or charger 
and remember to charge batteries to a capacity level of 40% to 60%. 
If batteries will be stored for long periods of time, RED  recommends 
that you check  the charge level at least once every six  (6) months, 
and recharge batteries to a capacity level of 40% to 60%.

When not in use, remove the battery from the camera or charger and 
store the battery in a cool, dry place. Avoid extreme hot temperatures 
(such   as  inside   a   hot  car),   corrosive   gas,   and  direct  sunlight.   The  
optimal storage temperature for batteries is between –20°C to 20°C (–
4°F to 68°F).

WARNING: 

Batteries stored in a discharged state 

for  long periods of time  may self-discharge  and 
lose the ability to hold a charge.

WARNING:  

If   recharging   operation   fails   to  

complete even when a specified recharging time 
has elapsed, immediately stop further recharging.

DO NOT store batteries in a fully charged state for extended 
periods of time.

DO NOT store batteries in a fully discharged state for extended 
periods of time.

DO NOT store batteries in the camera, in a camera module, or in 
a charger for extended periods of time.

DO NOT use batteries for purposes other than their intended use.

DO NOT store batteries in extreme hot or cold temperatures.

DO NOT store batteries in direct sunlight.

DO NOT use third-party chargers with your RED batteries.

DO NOT disassemble or modify the battery.

DO NOT overcharge batteries. Overcharging may increase 
internal temperature beyond the recommended limits and cause 
permanent damage to the battery.

DO NOT connect the positive (+) and negative (–) terminals to a 
metal object such as a wire.

DO NOT transport or store the battery together with metal objects 
such as jewelry, hairpins, etc. as they may generate heat if they 
come into contact with the battery.

DO NOT discard the battery into fire or heat.

C O PYR I G HT © 2 0 1 7 R ED.C O M , LLC

9 5 5 - 0 0 3 8 , R EV - AD   

|

   6

RED DSMC POWER OPERATION GUIDE

DO NOT store, use, or recharge the battery near a heat source 
such as a fire or a heater.

DO NOT allow the battery to get wet.

DO NOT pierce the battery with pointed or other sharp objects.

DO NOT step on, throw, or strike the battery with a hammer.

DO NOT use a battery that appears to be deformed or damaged.

DO NOT directly solder the battery.

DO NOT put the battery into a microwave oven or a pressurized 
container.

DO NOT use or subject the battery to intense sunlight or hot 
temperatures such as in a car in hot weather.

DO NOT use it in a location where static electricity may be 
present.

DO NOT exceed the recharging temperature range of 0˚C to 40˚C 
(32˚F to 104˚F).

RED recommends that you only use RED chargers to recharge 
RED batteries.

Store the battery in a location where children cannot reach it.

If the battery leaks or gives off a bad odor, discontinue use 
immediately.

If the battery gives off an odor, generates heat, becomes 
discolored or deformed, or in any way appears abnormal during 
use, recharging or storage, immediately remove it from the 
equipment or battery charger and discontinue use.

If electrolyte begins leaking from the battery and comes into 
contact with your skin or clothing, immediately wash it away with 
running water. Failure to do this may result in skin inflammation.

If the battery leaks and the electrolyte reaches the eyes, do not 
rub them. Instead, rinse the eyes with clean running water and 
immediately seek medical attention. Failure to do this may result in 
eye injury.

If you find discoloration, a bad odor due to leakage, overheating 
and/or other irregularities when using the battery for the first time, 
contact your Bomb Squad representative immediately.

NOTE:  

For   more   information   regarding   RED  

battery charging and instructions for care, please 
refer to our 

Terms and Conditions

.

SHIPPING DISCLAIMER

Unless you have  been certified to ship dangerous goods, you must 
work with a Dangerous Goods, Class 9-certified shipper to assist you 
with a  shipment that includes a  REDVOLT, REDVOLT-V, REDVOLT 
XL, and RED BRICK (or other regulated lithium ion batteries). Please 
note   that  applicable   laws  prohibit  the   shipping  of  batteries  that  are  
physically damaged. We  urge  you to look  into the  formal rules and 
regulations of shipping Class 9 Dangerous Goods prior  to preparing 
your shipment. For more information on these regulations, please visit 

www.iata.org

 and 

www.dot.gov

.

Summary of Contents for +1 ADAPTOR MODULE































































































Reviews: