red lion PXU10020, Instructions Manual

Page: 24 / 47

-24-
Drawing No. LP0932 Released 2018-01-12
ACCESS CODE
-125
to
125
7.3 MODULE 3 - Lockout Parameters (
3-LC
)
SETPOINT OUTPUT 1
POWER
CURRENT
TRANSFORMER
OUTPUT 2
POWER
CONTROLLER
STATUS
PID
GROUP RAMP RATE
SETPOINT PROFILE
STATUS
PROFILE
TIME
STARTING
PROFILE
STARTING
PROFILE
SEGMENT
PROFILE
INDICATOR
OUTPUT
POWER
OFFSET
PROPORTIONAL
BAND
INTEGRAL
TIME
DERIVATIVE
TIME
ALARM 2
VALUE
SETPOINT
SELECT
ALARM
RESET VALUE
ALARM 3 AUTO-TUNE
START
CONTROL
MODE
DEVIATION
VALUE
CONTROL
MODE
TRANSFER
ACCESS
CODE
P P
Programming/model dependent.
INTEGRATION
DEFAULT
ALARM 1
VALUE
SETPOINT
CONTROL
MODE
SETPOINT
2
SETPOINT
1
PARAMETER MENU
SELECTION DESCRIPTION
dIP
Display: accessible in Display Loop.
PArA
Parameter: accessible in Parameter Loop
Id
Hide: accessible in Hidden Loop.
LOC
Locked: not accessible in loops.
dPr
Display/read: read only in Display Loop, but read/write
in Hidden Loop.
The following parameters can be configured for the selections
described above. See Programming Loops section for a description of
loops and parameters.
PARAMETER SELECTION
FACTORY
SETTING
P dIP
,
PArA
,
Id
,
LOC
,
dPr dIP
C1 dIP
,
PArA
,
Id
,
LOC dIP
OP1 dIP
,
PArA
,
Id
,
LOC
,
dPr PArA
OP2 dIP
,
PArA
,
Id
,
LOC
,
dPr PArA
PrP dIP
,
PArA
,
Id
,
LOC
,
dPr PArA
PId dIP
,
PArA
,
Id
,
LOC
,
dPr PArA
r- dIP
,
PArA
,
Id
,
LOC
,
dPr dIP
P dIP
,
PArA
,
Id
,
LOC
,
dPr PArA
r-i dIP
,
PArA
,
Id
,
LOC
,
dPr PArA
ProF PArA
,
Id
,
LOC PArA
Pg PArA
,
Id
,
LOC LOC
Pind
♦
dIP
,
LOC dIP
OPOF PArA
,
Id
,
LOC PArA
ProP PArA
,
Id
,
LOC PArA
In PArA
,
Id
,
LOC PArA
dR PArA
,
Id
,
LOC PArA
dIn PArA
,
Id
,
LOC LOC
AL-1 PArA
,
Id
,
LOC PArA
AL-2 PArA
,
Id
,
LOC PArA
AL-3 PArA
,
Id
,
LOC PArA
ALr PArA
,
Id
,
LOC PArA
PL PArA
,
Id
,
LOC PArA
N Id
,
LOC Id
CrL Id
,
LOC Id
P Id
,
LOC LOC
rnF Id
,
LOC Id
0
Full access to Display, Hidden, and
Configuration Loops
-1 to -125
Code necessary to access
Configuration Loop only.
*
1
to
125
Code necessary to access Hidden
and Configuration Loops.
*
* If PLOC is active, Configuration Loop is not accessible.
0
Cod
Shaded parameters are programming/model dependent.
PARAMETER SELECTION
FACTORY
SETTING
dV dIP
,
LOC dIP
P1 dIP
,
PArA
,
Id
,
LOC dIP
P2 dIP
,
PArA
,
Id
,
LOC LOC
Parameters may not appear in selected loop if not applicable to
current operating mode.
Ex. 1. If
A2
=
NON
,
AL-2
will not be displayed in selected loop.
2. If
CrL
=
ONOF
, PID parameters will not be displayed in selected loop.
♦ Programming
Pind
for
diP
will enable the Profile Indicator segment, which
is located in the lower left of the unit display. When enabled the Profile
Indicator segment will flash to indicate that a profile is currently running.