Record S20 Series User Manual Download

Page: 27 / 34

Servicing and maintenance

BAL_S20_EN_1V0_REC_121-006454590

27/ 33

Test / inspection

Procedure

Expected result

Continuous floor guide (instead
of punctual door leaf guide)

▪

Set the door to manual ope-

ration (see chapter "Selecting
special functions")

▪

Clean all guides from dirt,

cigarette butts, etc.

▪

The door leaf must be pro-

perly guided

▪

The movement of the door

must not be obstructed by
dirt

Drive guard cover

▪

Check the fastening of the

drive guard cover

▪

It must be completely closed

and reliably engage in the
hinges

Protective wing (optional - de-
pending on national regulations)

▪

Check the mechanical condi-

tion of the protective wing

▪

In particular, check the clo-

sing mechanism

▪

A protective wing should

prevent all crushing and
shearing points

Summary of Contents for S20 Series



































Search results

Summary of Contents for S20 Series

Reviews:

Related manuals for S20 Series

Brands by name

Popular brands

Record S20 Series, User Manual

Search results

Summary of Contents for S20 Series

Reviews:

Related manuals for S20 Series

Brands by name

Popular brands