Rayjet R400 Operating Manual Download Page 52

Page: 52 / 83

❶

Standby-button.

LED On: Standby-Mode

❷

Status indicator laser beam.

LED On: The machine is processing data.

❸

Stop-button

❹

Start/Pause/Repeat-button

LED is flashing slowly green (every two seconds).

All covers are closed. Machine is ready.

LED is flashing fast green (twice per second).

Minimum one cover is open.

LEDs light up blue and green.

Data transfer complete. Pause-mode active. Job can

be started.

LED lights up green.

Job is running.

❺

Working table control button Z

•

Up-button

•

Down-button

❻

Exhaust-button.

LED On: Exhaust active

❼

Shift-button.

Second operating level

❽

Laser head control button X/Y

•

travel distance in X-direction

•

travel distance in Y-direction

❾

Home-button.

LED On: Temporary change of home position.

7.4.1 Description

Image

Button

Description

Status indicator

LED On: The machine is processing or receiving data.

Standby-button

LED On: Standby-mode

•

Press this button to switch to the Standby-mode.

•

Press the Standby-button while the working table is

moving up or down (e.g. by focus automatically).

The machine enters Standby-mode only after finishing

the movement.

Home-button

LED On: Temporary change of home position.

•

Press the Home-button for 3 seconds to temporarily

define the position of the laser head as home position

(Marker in JobControl®).

To deactivate the temporary home position press the

shortcut Shift- Home-button.

ENGLISH (Translation)

07/2021

52 / 83

Summary of Contents for R400




















































































Search results

Summary of Contents for R400

Reviews:

Related manuals for R400

Brands by name

Popular brands

Rayjet R400, Operating Manual

Search results

Summary of Contents for R400

Reviews:

Related manuals for R400

Brands by name

Popular brands