Rayco RG25HD Operator, Service, Maintenance, Parts Manual Download Page 44

Page: 44 / 72

RG25DH Operation • Service • Maintenance • Parts Manual

Troubleshooting

SYMPTOM

PROBLEM

CORRECTIVE ACTION

UNIT IS NOISY

Final drive gear noise

Check, add gear oil to ﬁnal drive

Check, replace worn gears

Check, replace worn bearings

Hydrostatic transmission noise

Replace hydrostatic transmission

Transaxle clicking

Mechanical disconnect not properly engaged,

check for obstruction

Check, replace mechanical disconnect

components (If hydrostatic transmission

shaft is damaged, replace transmission)

DOES NOT DRIVE

Improper belt tension

Belt worn, replace

(See O.E.M. equipment manual)

Brake setting incorrect

Adjust brake to proper setting

(See O.E.M. equipment manual)

Belt worn, glazed, or oil saturated

Replace belt

(See O.E.M. equipment manual)

Drive pulley worn

Replace pulley and belt

(See O.E.M. equipment manual)

Transaxle - hydrostatic transmission bad

Replace hydrostatic transmission

Shifter linkage misadjusted or broken

Linkage damaged or loose, replace or adjust

(See O.E.M. equipment manual)

Fluid low in hydrostatic transmission

Check and add ﬂuid if low (Part No. 730228A)

Disconnect is in freewheel position

Move control to connected position

(See O.E.M. equipment manual)

Sheared or missing axle key

Replace missing or broken key

Damaged or broken ﬁnal drive gear

Check, replace worn or damaged gear

Hydrostatic transmission leaking

Replace hydrostatic transmission

LEAKING LUBRICANT

Hydrostatic transmission leaking

Replace hydrostatic transmission

Final drive leaking at seam

Split ﬁnal drive housing, clean old sealant off,

replace seals, apply new sealant (torque bolts

80-120 in. lbs.[9.0 Nm - 13.5 Nm])

Final drive leaking at shaft seal

Split ﬁnal drive housing, clean old sealant off,

replace seals, apply new sealant (torque bolts

80-120 in. lbs. [9.0 Nm - 13.5 Nm])

BRAKE NOT WORKING

Linkage out of adjustment

Adjust brake linkage

(See O.E.M. equipment manual)

Linkage bent or broken

Replace components, set brake

(See O.E.M. equipment manual)

Brake setting incorrect

Adjust brake to proper setting

(See O.E.M. equipment manual)

TecumsehPower Transaxle Troubleshooting -

continued

Summary of Contents for RG25HD








































































Search results

Summary of Contents for RG25HD

Reviews:

Related manuals for RG25HD

Brands by name

Popular brands

Rayco RG25HD, Operator, Service, Maintenance, Parts Manual

Search results

Summary of Contents for RG25HD

Reviews:

Related manuals for RG25HD

Brands by name

Popular brands