Raven SCS 4600 Installation And Operation Manual Download Page 27

Page: 27 / 104

Manual No. 016-0159-925

CAN Networking and CAN Data Menu

Below are some common causes for communication failures:

Issue

Possible Cause

Solution

CANbus cannot read
the product node

• The node is not

connected to the CANbus

• Connect the node and reboot the SCS console to read the

product node.

• Node is not properly

powered

• Connect the clean power - 16 gauge red wire and high current

power - 12 gauge red wire from the product node to a 12V DC
power source that is capable of supplying power to all nodes
connected to the CANbus system

• Node is not properly

grounded

• Connect the clean ground - 16 gauge white wire and the high

current ground - 12 gauge white wire to a good, quality ground
source. Raven recommends grounding the wires to the
negative terminal of the battery.

• CANbus ends not

terminated

• Make sure that both ends of the CANbus system are properly

terminated. Refer to the Raven CANbus Installation Manual for
more information about installing terminators on the CANbus.

• Corroded pins in CANbus

connections

• Check CANbus cable connectors for any highly corroded pins.

• Ensure dielectric grease has been applied to all cable

connections exposed to weather and field conditions.

• Moisture in connection

• Check CANbus cable connectors for any corroded pins.

• Ensure dielectric grease has been applied to all cable

connections exposed to weather and field conditions.

• Connectors not seated

properly

• Check that all CANbus cable connectors are inserted fully (until

the locking tab is engaged).

• Be sure to remove any moisture in connections which were not

properly seated. Check for corroded pins and apply dielectric
grease when reconnecting CANbus cables.

Summary of Contents for SCS 4600








































































































Search results

Summary of Contents for SCS 4600

Reviews:

Related manuals for SCS 4600

Brands by name

Popular brands

Raven SCS 4600, Installation And Operation Manual

Search results

Summary of Contents for SCS 4600

Reviews:

Related manuals for SCS 4600

Brands by name

Popular brands