Raven SCS 4600 Installation And Operation Manual Download Page 31

Page: 31 / 104

Manual No. 016-0159-925 Rev. F

Installation

Connect the console cable to vehicle power as shown in the figures designated above. Refer to the

Raven

CANbus Network Installation Manual

for details on connecting the console to vehicle power using the

cabling platform installed on the vehicle.

Important:

Do not connect the red and white leads to the vehicle starter. Make sure the vehicle accessory power (key)
is off before routing the red and white battery leads to a 12-volt battery.

Secure the power leads with plastic cable ties but do not tie the power wires close to existing battery cables
or any other electrical wiring.

FIGURE 2.

SCS 4000/4070/5000 Series Console Connections

To CANbus
Connection

Summary of Contents for SCS 4600








































































































Search results

Summary of Contents for SCS 4600

Reviews:

Related manuals for SCS 4600

Brands by name

Popular brands

Raven SCS 4600, Installation And Operation Manual

Search results

Summary of Contents for SCS 4600

Reviews:

Related manuals for SCS 4600

Brands by name

Popular brands