Raritan IP-Reach IPR-M1 User Manual Download

Page: 65 / 84

HAPTER

DMINISTRATIVE

UNCTIONS

Type the server secret needed to authenticate against your remote authentication servers in the

Server Secret

field. Re-type the server secret in the

Confirm Secret

field.

Type the time of inactivity (in seconds) that should pass before the server times out in the

Server

Timeout (seconds)

field.

Type the IP addresses of your primary and secondary remote authentication servers in the

Primary Server IP

and

Secondary Server IP

fields.

If you selected LDAP as your remote authentication protocol, please read the next section

Implementing LDAP Remote Authentication

to complete the fields in the LDAP panel of the

Remote Authentication window. If you selected RADIUS, please skip to

Implementing RADIUS

Remote Authentication

to complete the fields in the RADIUS panel of the window.

Summary of Contents for IP-Reach IPR-M1





















































































Search results

Summary of Contents for IP-Reach IPR-M1

Reviews:

Related manuals for IP-Reach IPR-M1

Brands by name

Popular brands

Raritan IP-Reach IPR-M1, User Manual

Search results

Summary of Contents for IP-Reach IPR-M1

Reviews:

Related manuals for IP-Reach IPR-M1

Brands by name

Popular brands