background image

 

RR27T 

 

Range Road Enterprises Ltd 
Box 944 
Eckville AB T0M 0X0 
www.range-road.ca 

 

Page 21 

Range Road Equipment (Except Pellet Machines & Hammer Mills) 

 

This equipment comes with a 12 month warranty against Manufacturer’s defects and excludes 
wear parts. If any product or part is proved to be defective within 12 months from date of 
purchase, by reason of improper workmanship and/or material we will replace, or repair at Range 
Road Enterprises Ltd. discretion, that part or product at no charge to you, excluding any 
freight costs. Pellet Makers & Hammer Mills come with a 6 month warranty against 
Manufacturer’s defects and excludes wear parts. 

 

Items not covered: 

Wear parts –including Saw Bar, Saw Chain, Drive Sprocket, Lovejoy Coupling & Rubbers, Tires, Bearings, Etc. 
(Conveyor Belt – does not include rips or tears) 
 

The engine is warranted separately by the engine manufacturer

 (Honda, Lifan, Kohler, Princess 

Auto, Ducar, Etc.) 
 
The warranty begins on the date of sale and is warranted by Range Road Enterprises Ltd. to the original purchaser 
only.

 This Warranty does not cover items that have been damaged by accident, alteration, abuse or improper 

lubrication. 

 

If the equipment is used commercially (Over 50 cords of firewood per year for processor) or a rental, warranty 
for this product is limited to a period of 90 days from the date of purchase.  
 

Warranty cancellation 

Unauthorized modification voids the warranty, Including but not limited to, welding, engine modification, pump and 
hydraulic system modification. The warranty is void if the user violates the assembly and/or operating & 
maintenance instructions.

 

Range Road Enterprises Ltd. shall not be liable under any circumstances for any incidental or 
consequential damages or expenses of any kind, including but not limited to – the cost of equipment 
rental, loss of profits, or cost of hiring services to perform tasks normally performed by the equipment. 

Range Road Enterprises Ltd. obligation under this warranty shall be exclusively limited to repairing or 
replacing (at Range Road Enterprises Ltd. discretion) products which are determined by Range Road 
Enterprises Ltd. to be defective upon delivery F.O.B. (return freight paid by customer) Range Road 
Enterprises Ltd., and on inspection by Range Road Enterprises Ltd.. This warranty does not apply to 
defects due, directly or indirectly, to misuse, abuse, negligence, accidents, unauthorized repairs, 
alterations, lack of maintenance, acts of nature, or items that would normally be consumed or require 
replacement due to normal wear. In no event shall Range Road be liable for death, personal or property 
injury, or damages arising from the use of its products. Range Road Enterprises Ltd. does not issue 
credits or refunds on products purchased directly from a distributor or dealer.

 

Summary of Contents for RR27T






















Reviews: