Raisecom P100R001 Hardware Description Download Page 169

Page: 169 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

10 Data cards

Raisecom Proprietary and Confidential

144

10.3.5 LEDs

Table 10-15 lists LEDs on the 8V24H card.

Table 10-15

LEDs on the 8V24H card

LED

Color

Description

PWR

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

SYS

Green

System status LED



Green: the system is working improperly.



Off: the system is working improperly.



Blinking green: the system is working properly.

TD1–TD8

Green

Sending data LED



Blinking green: the corresponding channel is sending
data. The blinking frequency is related to the volume of
data being sent.



Off: the corresponding channel is not sending data.

RD1–RD8

Green

Receiving data LED



Blinking green: the corresponding channel is receiving
data. The blinking frequency is related to the volume of
data being received.



Off: the corresponding channel is not receiving data.

10.3.6 Internal jumper

Table 10-16 lists the internal jumper used by the 8V24H card.

Table 10-16

Internal jumper used by the 8V24H card

Jumper

Function

Status

Description

JP1

Configure the
mode for
downloading
the MCU
program.

Short-circuited

Enter ISP mode. In this mode, the
RC3000-15 is waiting to be upgraded.
You can upgrade MCU program through
the serial interface on the backplane.

Disconnected

Enter normal working mode.



By default, JP1 is disconnected; namely, MCU is in normal working mode.



After upgrade, JP1 must be disconnected; otherwise, the 8V24H card will
malfunction.

Summary of Contents for P100R001


















































































































































































































































































Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands

Raisecom P100R001, Hardware Description

Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands