Raisecom P100R001 Hardware Description Download Page 192

Page: 192 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

11 Multi-service card

Raisecom Proprietary and Confidential

167

Table 11-5

Parameters of the V.24 interface

Parameter

Description

Interface mode

DCE mode

Connector type

HDB26 female connector

Collection
frequency/Interface rate

64 kbit/s and 128 kbit/s

The corresponding bandwidth: 64 kbit/s and 128 kbit/s

Features

Complying with ITU-T V.24 recommendations

Electrical features

Complying with V.28 recommendations

Transmission distance

15 m (serial interface standards)

Table 11-6 lists parameters of the RS485 interface.

Table 11-6

Parameters of the RS485 interface

Parameter

Description

Connector type

RJ45

Collection
frequency/
Interface rate

64 kHz, 128 kHz, 256 kHz, 512 kHz, 1 MHz, and 2 MHz

The corresponding bandwidth: 64 kbit/s, 128 kbit/s, 256 kbit/s, 512
kbit/s, 1024 kbit/s, and 2048 kbit/s

Interface rate

The interface rate is related to the collection frequency:



The interface rate is up to 9.6 kbit/s when the collection frequency is
64 kHz.



The interface rate is up to 19.2 kbit/s when the collection frequency is
128 kHz.



The interface rate is up to 38.46 kbit/s when the collection frequency
is 256 kHz.



The interface rate is up to 57.6 kbit/s when the collection frequency is
512 kHz.



The interface rate is up to 115.2 kbit/s when the collection frequency
is 1 MHz.



The interface rate is up to 460.8 kbit/s when the collection frequency
is 2 MHz.

Compliant
standard

Complying with interface standards of RS485 and RS422 protocols

Interface PINs

For colors of the cable, see section 13.14 MUL cable.

Table 11-7 lists PIN definitions of the FXS/FXO interface on the 16MULTI card.

Summary of Contents for P100R001


















































































































































































































































































Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands

Raisecom P100R001, Hardware Description

Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands