Raisecom P100R001 Hardware Description Download Page 141

Page: 141 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

9 Asynchronous data cards

Raisecom Proprietary and Confidential

116

9.1.2 Version

Card

Version

RC3000-15-16RS232

9.1.3 Slots

Chassis version

Slot

E.30 and E.20

1–6 and 9–13

9.1.4 Interfaces

Interface type

Table 9-1 lists interfaces on the 16RS232 card. The maximum length of the cable used for the
RS232 interface is 15 m based on RS232 standard.

Table 9-1

Interfaces on the 16RS232 card

Name

Type

Description

1–8, 9–16

HDB26 female interface

Each interface outputs 8 ways of RS232 data.

Interface parameter

Table 9-2 lists parameters of interfaces on the 16RS232 card.

Table 9-2

Parameters of interfaces on the 16RS232 card

Parameter

Description

Connector type

HDB26 female connector

Compliant
standard

RS232 standard

Collection
frequency/Inter
face rate

64 kHz, 128 kHz, 256 kHz, 512 kHz, and 1 MHz

The corresponding interface bandwidth: 64 kbit/s, 128 kbit/s, 256
kbit/s, 512 kbit/s, and 1024 kbit/s

Summary of Contents for P100R001


















































































































































































































































































Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands

Raisecom P100R001, Hardware Description

Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands