Raisecom P100R001 Hardware Description Download Page 118

Page: 118 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

8 Voice cards

Raisecom Proprietary and Confidential

LED

Color

Description

SYS

Green

System status LED



Green: the system is working improperly.



Off: the system is working improperly.



Blinking green: the system is working properly.

1–10

Green

Yellow



E&M signaling status LED



Green: E signaling



Yellow: M signaling



On: the corresponding channel is receiving the E or M
signaling.



Off: the corresponding channel is idle.

When the E&M signaling is conducting internal
loopback, the LED indicates the status of the
physical status of the E signaling only.

8.4.6 Internal jumper

Location

There are multiple jumpers on the card, but you need to configure the E&M signaling jumper
only.

On the card, each interface provides a group of 4 E&M signaling jumpers.

Figure 8-5 shows the location of the E&M signaling jumper.

Summary of Contents for P100R001


















































































































































































































































































Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands

Raisecom P100R001, Hardware Description

Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands