Radstone PMCGA1-101 Product Manual Download Page 30 | Manualshive

Page: 30 / 113

background image

PPC7A Product Manual

Configuration

4-3

1

st

Edition

FLASH Write Enable Links (E3 and E9)

Each link enables or disables erasure/reprogramming of a section of the FLASH. E3 controls the User
FLASH and E9 controls the System FLASH. See Chapter 8 for details of FLASH operation.

S

ETTING

F

UNCTION

In

Enables erasure/reprogramming of the section of FLASH

Out (default)

Disables erasure/reprogramming of the section of FLASH

$

Note:

Regardless of any link settings for the FLASH write protection the Boot Recovery can’t be write enabled
and also the Boot data area can’t be write protected. See Chapter 8 for more details of these FLASH
areas.

VME Boot Link (E4)

This link holds the CPU in reset to allow a VME master to program boot code to the FLASH devices. To
program the boot code into the FLASH devices the VME master will need to program up both the
Universe and also the GT-64260 to allow a window from VME into the FLASH devices.

S

ETTING

F

UNCTION

In

VME programming mode

Out (default)

Normal boot mode

Use of this link relies on the default Universe II configuration (see the VMEbus Interface Configuration
section).

Overall FLASH Write Enable Links (E5)

This link enables or disables erasure/reprogramming of a both sections of the FLASH.

S

ETTING

F

UNCTION

In

Enables erasure/reprogramming of the FLASH

Out (default)

Disables erasure/reprogramming of the FLASH

$

Note:

To give more flexibility to the system builder, the FLASH can also be write enabled by linking pin A2 of
the P0 connector to Ground or Z1 of the P2 connector.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
28
29
30
31
32
...
»

Summary of Contents for PMCGA1-101


















































































































Reviews:

No comments

Related manuals for PMCGA1-101

cPCI-6841 Series

Brand: ADLINK Technology Pages: 76

IAC-F694 Series

Brand: Lanner electronics Pages: 61

IAC-H670 Series

Brand: Lanner electronics Pages: 49

WAFER-CV-D25501

Brand: IEI Technology Pages: 135

WAFER-EHL-J6412

Brand: IEI Technology Pages: 15

Brand: WinSystems Pages: 83

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands