RadioLink F450 Instruction Manual Download Page 20 | Manualshive

Page: 20 / 29

background image

RadioLink Electronic Ltd

www.RadioLink.com

15

Meanwhile, the selected mode on MP will turn dark green. That is , turning the dial on the transmitter to modify
the RATE to make sure the corresponding PWM value on MP is within the range. Flight mode 2/3/4/5/5 can be
set as the same way.

The 2-way switch is needed when setting Mode 4 to 6. Toggle this switch to the corresponding mode and

can be set as the above step 3.

2.2.3.3 Failsafe Setup

The function of Failsafe on Mini Pix is set with MP menu.
Entering the Failsafe menu on MP, a note will pop out to remind no propellers installed for safety.

Click OK to setup:

«
...
18
19
20
21
22
...
»

Summary of Contents for F450






























Reviews:

No comments

Related manuals for F450

Brand: Galaxy Pages: 8

SafeAir M-300 Pro

Brand: ParaZero Pages: 24

Brand: Skycat Pages: 27

Brand: Reely Pages: 25

riot zoopa Q 165

Brand: ACME Pages: 30

Brand: sky rider Pages: 24

PHANTOM 4 M-SPECTRAL

Brand: dji Pages: 12

X12 gyroscope explorers

Brand: SYMA Pages: 11

Brand: SYMA Pages: 36

Brand: HobbyKing Pages: 5

Brand: HobbyKing Pages: 15

AssaultReaper 500

Brand: HobbyKing Pages: 27

Brand: HOBBYEAGLE Pages: 38

Brand: Holy Stone Pages: 14

Brand: Firefly Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands