background image

- 34 -

RA_MA_DI_COMBIBIRD_CB_1510_EN

 - 11/15

M

aintenance

 cOMBiBiRD cB 

fOlDing

 

seMi

-

MOunteD

 

veRsiOn

MAINTENANCE

a

 CAUTION:

Observe the safety instructions (see Chap. 2) before 

starting service work or replacing spare parts. 

• The operator and the owner are responsible for the 

implement's maintenance.• Before commencing any 

work on the implement, switch off the engine and 

remove the tractor's ignition key. 

• Risk of trapping or crushing injuries during 

maintenance or cleaning. 

• Stabilise the implement before performing any 

maintenance or cleaning operations. 

• Make sure that the implement cannot be 

inadvertently operated while carrying out 

maintenance or cleaning work.

a

 CAUTION: 

Make sure that your safety is assured by the 

techniques used to raise the implement.

a

 CAUTION: 

Tyres must be fitted and removed by qualified 

personnel.

i

 IMPORTANT: 

The operator and the owner of the implement must 

not under any circumstances tamper with or adjust 

sealed components.

10 p

roTecTIon

 

of

 

The

 

envIronmenT

10.1  Soil contamination

i

 IMPORTANT: 

Take care not to spread waste grease and 

substances such as hydraulic oil on the ground or to 

dispose of them in the drains.

i

 IMPORTANT: 

Collect the drained hydraulic oil in sealed, clean and 

containers provided for this purpose.

10.2  Worn tyres

a

 CAUTION: 

It is prohibited to store, abandon, deposit tyres in 

the environment or to burn them in the open air. 

Take them to an approved dealer or collection point.

11 c

leanIng

Clean the implement.

 

When cleaning with a high pressure cleaner, do not direct the 

jet at joints, bearings etc. or at electrical components.

 

Pay special attention to safety stickers affixed to the 

implement. Damaged or detached stickers must be replaced.  

 

Do not use compressed air to clean hydraulic components.

 

Perform complete lubrication of the implement after each 

cleaning.

12 I

nspecTIon

i

 IMPORTANT: 

Inspect implement after each use and perform the 

required repairs.

 

Check the general state of the implement : 

 

-

The welds.

 

-

The wheels, tyres and the wheel studs.

 

-

The bolts of wearing parts under stony conditions (strong 

vibrations).

Summary of Contents for COMBIBIRD CB









































Reviews: