QTech 1U Hardware Installation Manual Download

Page: 89 / 221

Hardware installation manual

Qtech Platform 2U Server Product Technical Manual

www.qtech.ru

2.6.1.

6.1.2 Install Hard Disk

This motherboard supports SATA hard drives. For the best performance, when you want

to establish an array mode setting, please use hard drives with the same model and capacity

as much as possible.

Please follow the installation method below to construct a SATA RAID disk array:

Follow the instructions to install the SATA hard drive into the hard drive bay.

Connect the SATA signal cable to the signal cable interface on the back of the SATA
hard disk.

Connect the SATA power cable to the power connector on the back of the SATA hard
disk.

3.6.1.

6.1.3 Set RAID options in BIOS

1. As shown below: Enter Advanced, set to [RAID] mode in SATA Mode Selection item.

Summary of Contents for 1U






























































































































































































































Search results

Summary of Contents for 1U

Reviews:

Related manuals for 1U

Brands by name

Popular brands

QTech 1U, Hardware Installation Manual

Search results

Summary of Contents for 1U

Reviews:

Related manuals for 1U

Brands by name

Popular brands