manualshive.com logo in svg

QTech 1U, Hardware Installation Manual, Page: 200 / 221

Share
Download
QTech 1U Hardware Installation Manual Download Page 200

Hardware installation manual 

Qtech Platform 2U Server Product Technical Manual 

196 

 
 

www.qtech.ru 

 

 

Configure the hot spare disk: 

After RAID is configured, hot spare disks are generally configured to improve data security.  You 

can configure a global hot spare disk and a dedicated hot spare disk as required. 

 

 

Hot spares are used only for redundant RAID levels. 

 

The capacity of a hot spare is greater than the capacity of a RAID single member disk to 

contribute to that RAID. 

 

Only disks with Unconfigured Good configuration mode are hot-spare. 

1.

 

Configure the global hot spare disk 
1.1.

 

As shown in Figure 2-101, select the disk to be configured as a global hot spare on the 

PD Mgmt screen and press F2. 

Figure 2-101 Selecting a disk to be configured as a global hot spare disk 

Summary of Contents for 1U






























































































































































































































Reviews:

No comments