manualshive.com logo in svg

QTech 1U, Hardware Installation Manual, Page: 132 / 221

Share
Download
QTech 1U Hardware Installation Manual Download Page 132

Hardware installation manual 

Qtech Platform 2U Server Product Technical Manual 

128 

 
 

www.qtech.ru 

 

 

 

Configure the hot spare disk: 

After RAID is configured, hot spare disks are generally configured to improve data security.  You 

can configure a global hot spare disk or a dedicated hot spare disk as required. 

 

 

Hot spares are used only for redundant RAID levels. 

 

The capacity of a hot spare is greater than the capacity of a RAID single member disk to 

contribute to that RAID. 

 

Only disks with Unconfigured Good configuration mode are supported as hot spare disks. 

 

Configuring a global hot spare disk 

1.

 

As shown in Figure 3-18, select Drive Management from the RAID card configuration page 

and press Enter. 

Figure 3-18 RAID card configuration interface 

Summary of Contents for 1U






























































































































































































































Reviews:

No comments