Procom DGC-1010 Operating Instructions Manual Download

Page: 34 / 40

any parameter of

digital input 2 is

selected.

Digital

Input 3 Delay

Monitoring time for

programmable digital input.
Digital inputs are explained

above.

1-100 Sec

Action DIN 3

Select the

action when any
parameter of

digital input 3 is
selected.

Engine Shut Down

Warning

Engine Shut Down

No Action

Digital

Input 4 Delay

Monitoring time for

programmable digital input.
Digital inputs are explained

above.

1-100 Sec

Action DIN 4

Select the action
when any

parameter of
digital input 4 is

selected.

Engine Shut Down

Warning

Engine Shut Down

No Action

Digital

Input 5 Delay

Monitoring time for
programmable digital input.

Digital inputs are explained
above.

1-100 Sec

Action DIN 5

Select the action

when any
parameter of

digital input 5 is
selected.

Engine Shut Down

Warning

Engine Shut Down

No Action

Digital

Monitoring time for

programmable digital input.

1-100 Sec

Summary of Contents for DGC-1010









































Search results

Summary of Contents for DGC-1010

Reviews:

Related manuals for DGC-1010

Brands by name

Popular brands

Procom DGC-1010, Operating Instructions Manual

Search results

Summary of Contents for DGC-1010

Reviews:

Related manuals for DGC-1010

Brands by name

Popular brands