Procom DGC-1010 Operating Instructions Manual Download Page 31

Page: 31 / 40

tolerated before stopping the
Generator. This setting is not

available if (4)&(5) are disabled.

RPM

Source

RPM can be selected through MPU
or CAN Bus.

MPU

CAN Bus

Pick Up

RPM

This parameter specifies the
minimum RPM at which crank shall

be terminated.

900

200-3000

Cnk Dsc

LLOP Sw

Auto disconnects the crank
command on detection of Oil

pressure from switch.

Disabled

Enabled

Disabled*

Cnk Dsc
LLOP Sn

Auto disconnects the crank
command on detection of Oil

pressure from sensor.

Disabled

Enabled

Disabled*

Cnk Dsc Alt

Vol

The minimum voltage from

Charging alternator which shall be
deemed fit enough to disconnect

the crank.

Disabled*

3-40V

Service

Due Hr

Time, in hours, for next service
due. This is warning/reminder.

250

10-999 Hrs

Pick Up

KVA

warning

If the programmable Digital output

is programmed for “Load Warning”
The digital output shall be

activated on crossing the load KVA
above the programmed level.

1-9999

Reset KVA

warning

Once the load falls below this level

the above activated contact shall
be released.

1-9999

KVA

Warning

Delay

The supervision time for the above
2 parameters.

1-999 Sec

Summary of Contents for DGC-1010









































Search results

Summary of Contents for DGC-1010

Reviews:

Related manuals for DGC-1010

Brands by name

Popular brands

Procom DGC-1010, Operating Instructions Manual

Search results

Summary of Contents for DGC-1010

Reviews:

Related manuals for DGC-1010

Brands by name

Popular brands