Procom DGC-1010 Operating Instructions Manual Download Page 12

Page: 12 / 40

SEN LLOP

Connect to Oil pressure sensor

SEN HWT

Connect to High Water Temperature sensor

SEN Fuel

Connect to Fuel sensor

SEN Oil

Connect to Oil Temperature Sensor

MPU/W-Point

Input of MPU or W-Point from charging alternator

7.1.2 Configurable Digital Inputs

PIN

DESCRIPTION

NOTES

Prog. Debar

Switch to negative

Digital Input 1

Switch to negative

Digital Input 2

Switch to negative

Digital Input 3

Switch to negative

Digital Input 4

Switch to negative

Digital Input 5

Switch to negative

Digital Input 6

Switch to negative

Digital Input 7

Switch to negative

Digital Input 8

Switch to negative

7.1.3 Communications

PIN

DESCRIPTION

NOTES

CAN P

For CAN communication

CAN N

For CAN communication

Not Connected

RS-485(D+)

For RS-485 communication

RS-485(D-)

For RS-485 communication

Summary of Contents for DGC-1010









































Search results

Summary of Contents for DGC-1010

Reviews:

Related manuals for DGC-1010

Brands by name

Popular brands

Procom DGC-1010, Operating Instructions Manual

Search results

Summary of Contents for DGC-1010

Reviews:

Related manuals for DGC-1010

Brands by name

Popular brands