background image

6

MIXER GRINDER

The mixer-grinder is provided with a plug L19-30P type. To make a right connection, only it is necessary verify the appropriate size

and the grounding type receptacle (See Fig. 5).

Before completing the electrical connection, check the worm (4) and mixing blades (8) rotation. When grind button (GRIND) is

pressed, the worm and mixing blades must rotate at the same time (the worm must rotates counter clockwise). If only the mixing
blades rotates, push the stop button and unplug the equipment. Interchange 2 of 3 incoming power supply wires. Reconnect the
mixer-grinder to the power supply, turn it on and verify the rotation again. If the good operation is confirmed, then fix the connection
to the power supply. If you have any question regarding the connection of the Mixer-grinder, contact to your authorized dealer. The
above procedure only applies to Mixer-grinder with three phase connection.

IV.- OPERATION

CONTROL PANEL

The mixer-grinder has a control panel with three buttons for fully operation (See Fig. 6).

CAUTION!:

Unplug or disconnect the machine from the power supply before changing wires.

KMG-32

-

Mix (ON) button

. This option activates the mixing blades.

The machine will only mix the product.
-

Grind (ON) button

. This option activates both the mix

blades and the worm. The product will be grinded.
-

OFF (Stop) button

. This button turns the mixer-grinder off.

Note: If the equipment is mixing and the grind button is pushed (or vice versa), the motor will turn off and after 5 seconds

it is going to start making the next operation .

FOOTSWITCH OPERATION (IN SOME MODELS ONY)

Depending on the model, your Mixer-Grinder may be equipped with a Footswitch interrupter and a selector panel with three
different options (Fig. 7):

- Footswitch:

by selecting this option, the footswitch will be enable to operate disabling the control panel buttons.

- Push buttons:

Control panel will be enable disabling footswitch interrupter.

- Stand by:

With this option, neither the Footswitch nor control panel could be operated.

Summary of Contents for KMG-32














Reviews: