BRUSHLESS ANGLE GRINDER DIA 115MM
20V - BODY ONLY
MODEL NO:
CP20VAGX
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL SAFETY.
9
Disconnect the grinder from the mains power before changing accessories, servicing or performing any maintenance.
9
Maintain grinder and discs in good condition. Check moving parts and alignment. If necessary use an authorised service agent.
9
Replace or repair damaged parts.
Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
WARNING!
Always work with the grinder safety guard in place.
9
Wear approved safety goggles, ear defenders, gloves and, if grinder generates dust, a dust mask.
9
The grinding wheel or disc must only be changed by persons holding an appropriate grinding wheel certificate.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Use grinder in a suitable work area. Keep area clean, tidy and free from unrelated materials and ensure adequate lighting.
9
Maintain correct balance and footing,
DO NOT
over-reach. Ensure the floor is not slippery and wear non-slip shoes.
9
Use only approved grinding discs and only use the normal grinding surface.
9
Check grinding disc to ensure there are no splits, cracks or other damage (see Section 6). If in doubt do not use the disc.
9
Grinding discs must be securely attached before use, but not over-tightened.
9
Secure unstable workpiece with a clamp, vice or other adequate holding device and ensure the grinder is gripped with both hands.
9
Keep non-essential persons away from the working area, use screens if necessary.
8
DO NOT
operate the grinder if any parts are missing or the grinder is damaged.
8
DO NOT
use the grinder for a task it is not designed to perform.
8
DO NOT
operate the grinder where there are flammable solids, liquids or gasses.
WARNING! DO NOT
grind any materials containing asbestos.
8
DO NOT
get the grinder wet or use in damp or wet locations.
8
DO NOT
switch the grinder on whilst the disc is in contact with the workpiece.
8
DO NOT
cover the grinder air vents. To do so will overheat the machine.
8
DO NOT
touch the workpiece immediately after grinding, it will be very hot.
8
DO NOT
use the grinder as a fixed tool and
DO NOT
try to cool the grinding disc with water of other lubricants.
8
DO NOT
hold unsecured work in your hand and
DO NOT
touch the grinding disc whilst operating, or whilst plugged into the mains power.
8
DO NOT
leave the grinder running unattended, and
DO NOT
lay the grinder down whilst it is running.
8
DO NOT
operate the grinder when you are tired or under the influence of alcohol, drugs or intoxicating medication.
9
When not in use switch off grinder, remove plug from power supply and store in safe, dry, childproof area.
2.
i
INTRODUCTION
The 20V Series has been designed to suit users from the DIY enthusiast to the professional. These body only tools offer a one battery
fits all solution with a choice of 20V lithium batteries ranging from 2Ah to 4Ah, meaning costs can be kept down whilst quality remains
high. Quality, stylish, lightweight tools with durable composite housing and a soft grip making them comfortable and easy to use.
CP20VAGX Issue1 07/06/19
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear eye
protection
Wear a
mask
Wear ear
protection
Wear protective
gloves
DANGER OF FIRE/EXPLOSION HAZARD
WARNING! The grinding process can produce streams of sparks which are a potential source of ignition, especially when
grinding metal.
8
DO NOT use the grinder where there are flammable liquids, solids or gases.
8
DO NOT allow grinder sparks to make contact with the operator’s clothing or any other fabric such as cleaning rags. Fabrics
contaminated with flammable materials such as petrol, oil, grease, paint and solvents are a particular fire hazard.
9
To reduce the risk of clothing catching fire the operator should wear wool or cotton outer garments treated with a fire retardant
in preference to man-made fibres.
