Primus FF10 Programming Manual Download Page 95

Page: 95 / 136

100962 G PUBLICATION DATE 24 JUN 2008.DOC

PROGRAMMING MANUAL

DEPENDING THE FAILURE TYPE THE FULL CONTROL COMPUTER WILL START A SPECIFIC
PROCEDURE :

WHEN SAFETY IS INVOLVED

Full stop + tumble

: the program is stopped but will run the tumble sequence

Full stop + safety time

: the program is stopped and a safety time is started

Don’t start

: the program will not be started as long as the safety

conditions are not fulfilled

WHEN SAFETY IS NOT INVOLVED

Full stop + request for continue : a request to Continue ? the program is displayed

Skip + continue

: the actual cycle step is skipped and the program continues

with

the

step

Continue

: the program continues

SPECIAL CASES :

For E11:Fill Time failure and E14:Heating time failure after overruling and erasing the

failure message, you can restart or stop the sequence, as Continue ? will be displayed.

Possible cause :

- water supply inlets closed

- decreasing capacity of the heating elements

For E24:Defective Level sensor, E25:Defective Temperature sensor and E35:Wrong software

version the Failure message can only be erased by switching the power off and back on.

Fault 31:Initialisation fault inverter and 32:Verification fault inverter can be erased by switching

off the power. But as Fault 31 and 32 indicates that the frequency inverter is not loaded with the

correct parameter settings, the washing machine can be damaged when the inverter is functioning

with the wrong settings.

Do not use the washing machine before a technician has inspected the problem.

Fault 41:Service Due will occur over and over again until you have reset the cycle counter.

See Paragraph 8.5 how to reset the cycle counter.

Fault 57:Door Locked Continue >> START will occur when the “Door Lock Switch” stays locked

when opening the outer door on a MB90-140-180.

You can still unload the linen at the other compartments by overruling the error message by Pressing

the START button.

RESET KEY :

When you have overruled an error message and opened the door, Reset Key will be displayed.

This message warns the operator that the Key Switch is still in Program mode.

Before you can start a new program you have to turn the key switch back to Run mode.

)

Turn the key switch to Run mode.

! ! Reset Key ! !

Summary of Contents for FF10









































































































































Search results

Summary of Contents for FF10

Reviews:

Brands by name

Popular brands

Primus FF10, Programming Manual

Search results

Summary of Contents for FF10

Reviews:

Brands by name

Popular brands